Bosch CFB 840 Servicing Instructions Download Page 2 | Manualshive

Page: 2 / 56

background image

2

|

Table of contents

CFB 840

6 720 802 836 (2012/05)

Table of contents

Key to symbols and safety instructions . . . . . . . . . . . . . . . . . . . 4

Key to symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Safety regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Product information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Determined use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

EU Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . 4

Notes on commissioning . . . . . . . . . . . . . . . . . . . . . . . . . 5

Cleaning the control unit . . . . . . . . . . . . . . . . . . . . . . . . . 5

Product description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Scope of supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.7.1 Controller CFB 840 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.7.2 FM442/CMM 920 function module . . . . . . . . . . . . . . . . . 5

Setting instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Setting instructions and replacement instructions
for high limit safety cut-out (STB) . . . . . . . . . . . . . . . . . . 5

3.1.1 Setting and installation of the high limit safety cut-out . 5
3.1.2 Adjusting the high limit safety cut-out . . . . . . . . . . . . . . . 6
3.2

Setting instructions for boiler water thermostat (TR) . . 6

Controls and programming unit . . . . . . . . . . . . . . . . . . . . . . . . . 7

Control unit controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Programmer programming unit . . . . . . . . . . . . . . . . . . . . 8

Modules and their function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

CM431 controller module . . . . . . . . . . . . . . . . . . . . . . . . 9

NM482 power supply module . . . . . . . . . . . . . . . . . . . . 10

Central module ZM422 . . . . . . . . . . . . . . . . . . . . . . . . . 10

5.3.1 Burner function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.3.2 Heating circuit and DHW functions . . . . . . . . . . . . . . . . 11
5.4

FM442/CMM 920 function module (accessory) . . . . . 11

Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Commissioning the programming unit . . . . . . . . . . . . . 12

6.1.1 New Programmer installed in a control unit . . . . . . . . . 12
6.1.2 Programmer is installed in another control unit . . . . . . 12
6.1.3 Programmer with set parameters installed

in control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Checking the high limit safety cut-out (STB) . . . . . . . . . 13

6.2.1 Triggering the high limit safety cut-out . . . . . . . . . . . . . 13
6.2.2 Terminating or cancelling the test . . . . . . . . . . . . . . . . . 13
6.2.3 Resetting the high limit safety cut-out . . . . . . . . . . . . . . 14

Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Adjustable parameters and display data . . . . . . . . . . . . 15

Calling up the service level . . . . . . . . . . . . . . . . . . . . . . . 16

7.2.1 Control system "Press and turn" . . . . . . . . . . . . . . . . . . 16
7.2.2 Calling up main menus . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.2.3 Calling up submenus . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.3

Calling up and modifying settings . . . . . . . . . . . . . . . . . 16

General specification data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Minimum outside temperature . . . . . . . . . . . . . . . . . . . 17

Type of building . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Summer/wintertime changeover . . . . . . . . . . . . . . . . . 18

Remote adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Manual fault message control . . . . . . . . . . . . . . . . . . . . 19

Automatic maint. message . . . . . . . . . . . . . . . . . . . . . . 19

Module selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Boiler parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Select boiler type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

9.1.1 Low temperature boilers  . . . . . . . . . . . . . . . . . . . . . . . .  20
9.1.2 Ecostream boilers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  21
9.1.3 Condensing boiler  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  21
9.1.4 Low-temperature boilers with base temperature . . . . .  21
9.2

Setting the burner type . . . . . . . . . . . . . . . . . . . . . . . . . 22

9.2.1 Modulating burner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
9.2.2 2 x single stage burner . . . . . . . . . . . . . . . . . . . . . . . . . . 22
9.3

General settings regarding boiler parameters . . . . . . . 23

9.3.1 Set up the pump function  . . . . . . . . . . . . . . . . . . . . . . .  23
9.3.2 Setting boiler pump run-on time  . . . . . . . . . . . . . . . . . .  23
9.3.3 Setting the minimum burner runtime  . . . . . . . . . . . . . .  23
9.3.4 Selecting the minimum start temperature  . . . . . . . . . .  23
9.3.5 Selecting the maximum shutdown temperature  . . . . .  24
9.3.6 Setting the maximum flue gas temperature limit  . . . . .  24

10 Heating circuit data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Adjusting the heating system . . . . . . . . . . . . . . . . . . . . . 24

Rename the heating circuit . . . . . . . . . . . . . . . . . . . . . . 25

Setting the low end temperature . . . . . . . . . . . . . . . . . . 25

Setting the design temperature . . . . . . . . . . . . . . . . . . . 25

Setting the Minimum flow temperature . . . . . . . . . . . . 26

Setting the maximum flow temperature . . . . . . . . . . . . 26

Select the remote control . . . . . . . . . . . . . . . . . . . . . . . 26

Maximum room influence setting . . . . . . . . . . . . . . . . . 27

Select the type of setback . . . . . . . . . . . . . . . . . . . . . . . 27

10.10 Setting the outside stop temperature . . . . . . . . . . . . . .  28
10.11 Setting holiday mode . . . . . . . . . . . . . . . . . . . . . . . . . . .  28
10.12 Stopping setback at low outside temperatures  . . . . . .  28
10.13 Setting flow setback . . . . . . . . . . . . . . . . . . . . . . . . . . . .  29
10.14 Setting the room temperature offset  . . . . . . . . . . . . . .  29
10.15 Automatic adaptation setting  . . . . . . . . . . . . . . . . . . . .  29
10.16 Setting switching optimisation  . . . . . . . . . . . . . . . . . . .  30
10.17 Set switch off optimisation time  . . . . . . . . . . . . . . . . . .  30
10.18 Setting frost protection temperature  . . . . . . . . . . . . . .  31
10.19 Setting DHW priority  . . . . . . . . . . . . . . . . . . . . . . . . . . .  31
10.20 Setting the heating circuit actuator . . . . . . . . . . . . . . . .  31
10.21 Set the actuator run-time . . . . . . . . . . . . . . . . . . . . . . . .  32
10.22 Setting the Boiler raising  . . . . . . . . . . . . . . . . . . . . . . . .  32
10.23 Setting the external changeover  . . . . . . . . . . . . . . . . . .  32
10.24 External fault message - pump . . . . . . . . . . . . . . . . . . . .  33
10.25 Screed drying  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33
10.25.1 Setting the temperature rise  . . . . . . . . . . . . . . . . . . . .  34
10.25.2 Setting the heat-up time . . . . . . . . . . . . . . . . . . . . . . . .  34
10.25.3 Setting the maximum temperature  . . . . . . . . . . . . . . .  34
10.25.4 Setting the hold time . . . . . . . . . . . . . . . . . . . . . . . . . . .  35
10.25.5 Setting the setback temperature  . . . . . . . . . . . . . . . . .  35
10.25.6 Setting the setback time . . . . . . . . . . . . . . . . . . . . . . . .  35

«
1
2
3
4
...
»

Summary of Contents for CFB 840

























































Reviews:

No comments

Related manuals for CFB 840

ControlMaster CM15

Brand: ABB Pages: 28

Brand: BADLANDS Pages: 2

Brand: FAAC Pages: 4

Brand: FAAC Pages: 52

Brand: ZIGBEE Pages: 5

Brand: Ziton Pages: 36

Brand: National Instruments Pages: 17

Brand: Davey Pages: 12

Brand: Veichi Electric Pages: 8

Brand: Mutable Instruments Pages: 2

Brand: Purelogic Pages: 60

ServLink ACR3500A

Brand: Black Box Pages: 115

GLOFA G7M-DR20U

Brand: LS Industrial Systems Pages: 367

Brand: Vixen Horns Pages: 2

ESCALA Power7 5802

Brand: Bull Pages: 48

Brand: Berkeley Pages: 8

Brand: ZIEHL-ABEGG Pages: 24

Brand: IFM Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands