Bosch CFB 840 Servicing Instructions Download Page 33

Page: 33 / 56

Heating circuit data

6 720 802 836 (2012/05)

CFB 840

Hold down button

Display

and turn the rotary dial until the required

value is shown.

Fig. 48 Setting the external changeover

Release

Display

to save your input.

Press

Back

to return to the next higher level.

10.24 External fault message - pump

This function is turned off at in factory setting.
This menu item determines whether fault messages relating to a pump

should be displayed.
You may connect an external volt free fault contact to terminals WF1 and

WF2. A fault message will be displayed if the contact is open.

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Turn the rotary dial until main menu

Heat.circuit

+ No. is displayed.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

External fault

message pump

appears.

Hold down button

Display

and turn the rotary dial until the required

value is shown.

Fig. 49 External fault message - pump

Release

Display

to save your input.

Press

Back

to return to the next higher level.

10.25 Screed drying

If the heating system comprises underfloor heating, this control unit a

drying program for the screed can be entered. As heating system

Under-

floor

must be set.

After a power failure, screed drying continues from where it was

interrupted.

Fig. 50 Screed drying

[x]

Time (days)

[y]

Temperature

[a]

3 days' hold time

[b]

Temp increase by

[c]

max. temperature

[d]

Setback by

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Turn the rotary dial until main menu

Heat.circuit

+ No. is displayed.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

Screed drying

appears.

Input range

Factory setting

External day/night/aut none

day via WF1/3

via WF1/2/3

none

Table 63 Setting range External changeover

Terminals WF1 / 2 / 3 of the control unit can be used in

either of the areas DHW, heating circuit 1 or heating

circuit 2.

If under menu option

External day/night/aut via WF1/

2/3

has been entered, this menu item cannot be called

up since the input contact is already allocated

HEAT CIRC. DATA 2
External
Day/night/aut

via WF1/2/3

6 720 802 836-62.1TL

HEAT CIRC. DATA 2
External fault
message pump

via WF1/2

6 720 802 836-63.1TL

Input range

Factory setting

External fault

message pump

none

via WF1/2

none

Table 64 Setting range External fault message - pump

Check with your screed contractor for special

requirements for screed drying prior to enabling this

function.

6 720 803 703-64.1T

Summary of Contents for CFB 840

























































Search results

Summary of Contents for CFB 840

Reviews:

Related manuals for CFB 840

Brands by name

Popular brands

Bosch CFB 840, Servicing Instructions

Search results

Summary of Contents for CFB 840

Reviews:

Related manuals for CFB 840

Brands by name

Popular brands