Bosch CFB 840 Servicing Instructions Download Page 32

Page: 32 / 56

Heating circuit data

CFB 840

6 720 802 836 (2012/05)

10.21 Set the actuator run-time

This parameter determines the run-time of the existing actuators. Most

actuators have a runtime of 120 s.

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Turn the rotary dial until main menu

Heat.circuit

+ No. is displayed.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

Actuator run time

appears.

Hold down button

Display

and turn the rotary dial until the required

value is shown.

Fig. 46 Set the actuator run-time

Release

Display

to save your input.

Press

Back

to return to the next higher level.

10.22 Setting the Boiler raising

If the temperature in a heating circuit is controlled with a mixing valve, a

higher set value should be set for the boiler, than the normal set value for

the heating circuit.
The value

Boil. raising

corresponds to the temperature differential

between the set boiler temperature and the set heating circuit

temperature.

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Turn the rotary dial until main menu

Heat.circuit

+ No. is displayed.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

Boil. raising

appears.

Hold down button

Display

and turn the rotary dial until the required

value is shown.

Fig. 47 Setting the Boiler raising

Release

Display

to save your input.

Press

Back

to return to the next higher level.

10.23 Setting the external changeover

Either of the following two changeover functions can be selected:

•

1. changeover

Day/night via the terminals WF1 and WF3

–

Contact WF1 and WF3 closed = day mode

–

Contact WF1 and WF3 open = night mode

•

2. changeover

day/night/aut via terminals WF1, WF2, WF3

–

Contact WF1 and WF3 closed = day mode

–

Contact WF1 and WF2 closed = night mode

–

all contacts open = automatic mode

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Turn the rotary dial until main menu

Heat.circuit

+ No. is displayed.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

External day/night/aut

appears.

If a constant oscillation of the mixing valve is noticeable,

slow down the control characteristics by reducing the

actuator runtime. Then the constant cycling of the mixing

valve should stop.

Input range

Factory setting

Actuator run time

10 sec – 600 sec

120 s

Table 61 Setting range Actuator runtime

HEAT CIRC. DATA 2
Actuator
run time

90sec

6 720 802 836-60.1TL

Input range

Factory setting

Boil. raising

0 °C – 20 °C

5 °C

Table 62 Setting range Boiler raising

Menu item

External changeover

is only displayed if

under menu option

Remote control

–

none

has been

selected and control unit CFB 840 is installed.

The menu item is also not shown if heating system

Room

thermostat

is selected since this requires a remote

control to be installed.

Terminals WF1 / 2 / 3 of the control unit can be used in

either of the areas DHW, heating circuit 1 or heating

circuit 2.

Activation

2. Changeover

is only possible if terminals

WF1 and WF2 via the

External fault message - pump

are not allocated.

Day mode will run constantly if both contacts are

simultaneously closed.

HEAT CIRC. DATA 2

Boil.raising

6 720 802 836-61.1TL

Summary of Contents for CFB 840

























































Search results

Summary of Contents for CFB 840

Reviews:

Related manuals for CFB 840

Brands by name

Popular brands

Bosch CFB 840, Servicing Instructions

Search results

Summary of Contents for CFB 840

Reviews:

Related manuals for CFB 840

Brands by name

Popular brands