Bosch CFB 840 Servicing Instructions Download Page 40

Page: 40 / 56

DHW data

CFB 840

6 720 802 836 (2012/05)

Fig. 69 Setting range Daily heat-up

Release

Display

to save your input.

Press

Back

to return to the next higher level.

11.11 DHW circulation pump

11.11.1 Selecting the DHW circulation pump

The function

DHW circulat.

ensures that DHW is immediately available

at the draw-off points.

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Turn the rotary dial until main menu

DHW

appears.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

DHW Circulat.

appears.

Hold down button

Display

and turn the rotary dial until the required

value is shown.

Fig. 70 Selecting the DHW circulation pump

Release

Display

to save your input.

Press

Back

to return to the next higher level.

11.11.2 Setting intervals

Operation in intervals saves operating costs for the circulation pump.

The function

DHW circulation per hour

ensures that DHW is

immediately available at the draw-off points.
The set interval applies during the period when the time program

enables the DHW circulation pump. This comprises:

•

The factory-set DHW circulation pump program

•

Your own DHW circulation pump program

•

A connection to the heating circuit switching times.

In constant mode the DHW circulation pump operates continuously

when in day mode, and is switched off in night mode.

Example

A proprietary time programme was entered that, within the period of

05:30 hours – 22:00 hours and when setting

DHW circulation is

enabled, turns on the

circulation pump 2 times per hour.

The circulation pump is enabled in cycles:

•

at 05:30 h for 3 minutes

•

at 06:00 h for 3 minutes

•

at 06:30 h for 3 minutes

•

etc., until 22:00 hours

Setting intervals

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Turn the rotary dial until main menu

DHW

appears.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

DHW Circulat. per hour

appears.

Hold down button

Display

and turn the rotary dial until the required

value is shown.

Fig. 71 Setting intervals

Release

Display

to save your input.

Press

Back

to return to the next higher level.

If the DHW was heated to 60 °C within the last 12 hours,

it is not heated at the specified time.

Input range

Factory setting

Daily Heat-up

inactive

00:00 – 23:00 hours

Inactive

Table 85 Setting range Daily heat-up

Input range

Factory setting

DHW Circulat.

yes

Table 86 Setting range DHW circulation

DHW Data
Daily
Heat-up

18:00

6 720 802 836-89.1TL

DHW Data

DHW Circulat.

6 720 802 836-90.1TL

Input range

Factory setting

DHW Circulat.

per hour

Off

1 time on

2 times on

3 times on

4 times on

5 times on

6 times on

Const. operation

2 times on

Table 87 Setting range DHW circulation per hour

DHW Data
DHW Circulat.
per hour

off

6 720 802 836-91.1TL

Summary of Contents for CFB 840

























































Search results

Summary of Contents for CFB 840

Reviews:

Related manuals for CFB 840

Brands by name

Popular brands

Bosch CFB 840, Servicing Instructions

Search results

Summary of Contents for CFB 840

Reviews:

Related manuals for CFB 840

Brands by name

Popular brands