Bosch CFB 840 Servicing Instructions Download Page 41

Page: 41 / 56

Special parameter

6 720 802 836 (2012/05)

CFB 840

Special parameter

This parameter enables Bosch service engineers to optimise the system

beyond the standard parameters by fine-tuning the sub-parameters.
This level is reserved for Bosch service engineers. Therefore, settings

are not made in plain text but in code. These are explained in a separate

document.

Heating curve

With menu

Heating curves

the current heating curves of all heating

circuits can be displayed.
The flow temperatures (VL), which depend on the outside temperature

(AT), are displayed.

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Turn the rotary dial until main menu

HEATING CURVE

appears.

Press

Display

to call up a submenu.

Turn the rotary dial to display the heating curves of all heating circuits.

Fig. 72 Heating curve

Press

Back

to return to the next higher level.

Relay test

provides a check whether the external components

(e.g. pumps) are working correctly.
The display depends on which modules are installed. Depending on the

current operating conditions, there may be a time delay between

demand and display.

With the modules used most commonly in the control units, the following

relays can be called up:

•

Boiler

–

Burner

–

Actuator

–

Boiler pump (if enabled)

•

Heating circuit 0 – 4

–

Circulation pump

–

Actuator (not on heating circuit 0)

•

Domestic hot water

–

Cylinder primary pump

–

DHW circulation pump

Relay test example

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Turn the rotary dial until main menu

Relay test

appears.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

Heating circ. 2

appears.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

Actuator

appears.

Hold down button

Display

and turn the rotary dial until the required

value is shown.

Fig. 73 Relay test

Release

Display

to save your input.

Press

Back

twice to return to the next higher level.

The relay test is terminated.

Carrying out an LCD test

With menu

LCD test

it can be checked whether all signs and symbols are

fully displayed.

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Turn the rotary dial until main menu

LCD test

appears.

Press button

Display

The LCD is OK, when all symbols are correctly displayed.

Press

Back

to return to the next higher level.

CAUTION:

System damage through disabled functions!

The supply of heat to the heating system is not

guaranteed during the relay test. The control system

disables all functions.

Function

Relay test

must be stopped at the end of the

test to prevent damage to the system.

HEATING CURVE
Heating circ. 2
OT: 10 / 0 / -10
VL: 45 / 62 / 75

6 720 802 836-93.1TL

At the end of the Relay test, all settings are cancelled.

RELAY TEST 2
Heating circ. 2
Actuator

closed

6 720 802 836-94.1TL

Summary of Contents for CFB 840

























































Search results

Summary of Contents for CFB 840

Reviews:

Related manuals for CFB 840

Brands by name

Popular brands

Bosch CFB 840, Servicing Instructions

Search results

Summary of Contents for CFB 840

Reviews:

Related manuals for CFB 840

Brands by name

Popular brands