Bosch CFB 840 Servicing Instructions Download Page 25

Page: 25 / 56

Heating circuit data

6 720 802 836 (2012/05)

CFB 840

10.2 Rename the heating circuit

Instead of the designation

Heat.circuit

+ No. another name can be

selected from a list provided.

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Turn the rotary dial until main menu

Heat.circuit

+ No. is displayed.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

Heating circ. desig.

appears.

Fig. 27 Rename the heating circuit

Hold down button

Display

and turn the rotary dial until the required

value is shown.

Release

Display

to save your input.

Press

Back

to return to the next higher level.

10.3 Setting the low end temperature

This function will only be displayed for "Low end" heating systems.
By setting

the heating system to Low end,

the system is set to a straight

heating curve using the low end and design temperatures.
The base point [Low end] temperature determines the start of the

heating curve. The low end temperature is applicable for an outside

temperature of 20 °C.

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Turn the rotary dial until main menu

Heat.circuit

+ No. is displayed.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

Heating system

appears.

Hold down button

Display

and turn the rotary dial until the required

value is shown.

Release

Display

to save your input.

Turn the rotary dial until submenu

Base point temp.

appears.

Hold down button

Display

and turn the rotary dial until the required

value is shown.

Fig. 28 Setting the low end temperature

Release

Display

to save your input.

Press

Back

to return to the next higher level.

10.4 Setting the design temperature

The design temperature is the flow temperature at the adjusted

minimum outside temperature.

For the heating system

Low end

the following applies:

•

Set the design temperature at least 10 °C higher than the low end

temperature.

•

Changing the design temperature allows the heating system to

operate with a flatter or steeper heating curve.

Call up the service level.

GENERAL PARAM.

appears as the first main menu.

Turn the rotary dial until main menu

Heat.circuit

+ No. is displayed.

Press

Display

to call up a submenu.

Turn the rotary dial until submenu

Design temp.

appears.

Hold down button

Display

and turn the rotary dial until the required

value is shown.

Fig. 29 Setting the design temperature

Release

Display

to save your input.

Press

Back

to return to the next higher level.

Input range

Factory setting

Heating system

none

Radiator

Convector

Underfloor

Constant

Low end

Room controller

Radiator

Table 38 Setting range Heating system

Input range

Factory setting

Heat circ. desig

Heating circ.

Apartment

Underfloor

Bathroom

Swimming pool

Floor

Cellar

Building

Heating circ.

Table 39 Setting range Heating circuit name

HEAT CIRC. DATA 2

Heat circ desig.

Heating circ.

6 720 802 836-41.1TL

Input range

Factory setting

Base point temp.

20 °C – 80 °C

30 °C

Table 40 Setting range Low end temperature

Observe the information regarding setting the heating

curves.

HEAT CIRC. DATA 2

Base point temp.

6 720 802 836-42.1TL

HEAT CIRC. DATA 2

Design temp.

6 720 802 836-43.1TL

Summary of Contents for CFB 840

























































Search results

Summary of Contents for CFB 840

Reviews:

Related manuals for CFB 840

Brands by name

Popular brands

Bosch CFB 840, Servicing Instructions

Search results

Summary of Contents for CFB 840

Reviews:

Related manuals for CFB 840

Brands by name

Popular brands