manualshive.com logo in svg

Bosch CFB 840, Servicing Instructions

Share
Download
Bosch CFB 840 Servicing Instructions Download Page 16

16

 | 

General specification data

CFB 840

6 720 802 836 (2012/05)

7.2

Calling up the service level

B

Press buttons 

Display

, 

Heating circuit

 and 

Temp

 simultaneously and 

release.

Fig. 17 Calling up the service level

[1]

Temperature key

[2]

Display key

[3]

Heating circuit key

The service level is enabled and the display shows:

Fig. 18 Service level

7.2.1 Control system "Press and turn"

The control unit is controlled by pushing the buttons or turning the rotary 

dial.
The Service level is split over several main menu levels. If the last line is 

left blank (without value entry), there are further submenus connected 

to the main menu selected.

7.2.2 Calling up main menus

The rotary dial is used to scroll through the main menu. The main menus 

are structured as a loop and recommence after the last main menu.

•

GENERAL PARAM.

•

Module selection

•

...

•

GENERAL PARAM.

7.2.3 Calling up submenus

B

Turn the rotary dial until the main menu containing the submenu is 

highlighted.

B

Press button 

Display

.

The submenu is shown.

B

Turn the rotary dial to access all submenus of the main menu.

7.3

Calling up and modifying settings

B

Calling up the service level (

Æ

 chapter 7.2, page 16).

GENERAL PARAM.

 appears as the first main menu.

B

Press 

Display

 to call up a submenu.

The display shows the selected submenu.

B

Press and hold 

Display

.

B

Turn the rotary dial to the required value.

The display shows the set value.

B

Release 

Display

 to save your input.

B

Press 

Back

 to return to the next higher level.

To return to the standard display:

B

Press 

Back

 several times.

8

General specification data

B

Call up the service level.

GENERAL PARAM.

 appears as the first main menu.

B

Press Display to call up a submenu.

B

Turn the rotary dial until the required submenu is shown.

Turn the rotary dial to scroll through the following submenus:

•

Minimum outside temperature

•

Type of building

•

Summer/wintertime changeover

•

Remote adjust.

•

Amount of heat

•

Manual fault message control

•

Automatic maint. message

B

Press button 

Display

 to call up a submenu.

The display shows the selected submenu, and settings can be made.

Access to the Service level is password protected. The 

Service level is only intended for heating contractors. 

Unauthorised access to the service level invalidates your 

warranty.

AUT

2

3

1

6 720 803 703-18.1T

SERVICE LEVEL   

Gen. Parameters

6 720 802 836-19.1TL

The menus displayed on the programming unit of the 

control unit depend on which modules are fitted and on 

their settings.

The control unit automatically reverts to the standard 

display if no key is pressed for some time or if the flap is 

shut.

In main menu 

GENERAL PARAM.

 values can be adjusted 

for the submenus listed above and the building 

characteristics. The following pages explain how to 

adjust values relating to the submenus.

Summary of Contents for CFB 840

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands