Bosch AVENAR 8000 User Manual Download Page 38 | Manualshive

Page: 38 / 94

background image

38

en | Alarm

FPA-5000 | FPA-1200 | AVENAR panel 8000 |

AVENAR panel 2000 | AVENAR keypad 8000

2020-07 | 3.0 | F.01U.378.877

User Guide

Bosch Sicherheitssysteme GmbH

Address of logical zone

00005: the fifth logical zone triggered the first fire alarm.

Number of detectors

(6): In the fifth logical zone (00005), six detectors (6) triggered a fire alarm.
For logical zones that only consist of one element, no number of detectors is displayed.

Notice!

Depending on the configuration of the system, either the logical or physical address of the
detector is displayed.

Message number

The alarm messages are numbered chronologically.
The message number in the second line indicates the sequence in which the alarm messages
arrived.
#001: The first alarm message that came in.
Depending on the configuration, additional information is displayed in the second line, such as
the installation location of the logical zone.

8.4.5

The newest message

The latest message is always displayed at the end of the list.
The message number (e.g. #008) of the latest message indicates the total number of logical
zones in which one or more detectors have triggered an alarm.

8.4.6

Displaying the individual detectors in a logical zone

To display the individual detectors in a logical zone, select the logical zone you require.
The alarm messages for the individual detectors are listed.

8.4.7

Information about individual detectors

Each alarm message contains information about:
–

The element category

–

The message type

–

The detector address

–

The message number

–

Depending on the configuration, additional information such as the installation location

Example:

Fire

Detectors

00005 - 004

#002

Office 1

Message type

Refer to Information about logical zones in the alarm state for information on the type of
message.

Message address

In this example, the following detector has triggered a fire alarm:
0005 - 004: the fourth detector (004) in the fifth logical zone (00005).
If the detector number, in this case (004), is not displayed, this is the alarm message for the
logical zone.

«
...
36
37
38
39
40
...
»

Summary of Contents for AVENAR 8000































































































Reviews:

No comments

Related manuals for AVENAR 8000

Brand: Lattice Semiconductor Pages: 30

Brand: WAFER Pages: 15

Brand: Vasco Pages: 32

Brand: Abra Pages: 16

Brand: SAI Pages: 16

Brand: Hable Pages: 3

Brand: IBM Pages: 38

Brand: WAREMA Pages: 112

Brand: WAGO Pages: 414

Brand: V2 Pages: 48

Brand: YOKOGAWA Pages: 150

Brand: YOODA Pages: 3

Brand: YMGI Pages: 8

Cutler-Hammer LMR

Brand: Eaton Pages: 38

HmIP-FAL230-C10

Brand: HomeMatic Pages: 42

SaunaLogic SL2 Control

Brand: Finnleo Pages: 14

Brand: Beckhoff Pages: 30

Brand: Festo Pages: 109

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands