Bosch AVENAR 8000 User Manual Download Page 56

Page: 56 / 94

en | Diagnostics

FPA-5000 | FPA-1200 | AVENAR panel 8000 |

AVENAR panel 2000 | AVENAR keypad 8000

2020-07 | 3.0 | F.01U.378.877

User Guide

Bosch Sicherheitssysteme GmbH

Diagnostics

This chapter contains information about the following points:
–

Element details, page 56: Diagnostic information about an LSN module and about
elements of a selected LSN module

–

Modules, page 57: Diagnostic information (software version) and hardware diagnostic
data about modules

–

Hardware, page 57: Information about released addresses, statistical data for the
transmission, and the execution of display tests

–

Panel Passport, page 58: Diagnostic information about the panel controller

–

LED Test on modules, page 58: Testing the LED display of modules

–

Network services, page 58: Information on the availability of other nodes within the
system network

–

Voice alarm systems, page 61: Diagnostic information about a connected voice alarm
system (VAS)

13.1

Menu overview

Diagnostics

Element details

Modules

Hardware

Panel passport

LED test on modules

History log

Network services

VAS

13.2

Element details

To display diagnostic information about the elements in a particular module:
1.

In the start menu, select

Diagnostics

Element details

A list of the LSN modules is displayed.

Notice!

The numbers before the module names indicate the slot of the module on the panel.

Select the list field you require.
On the display, various possibilities for selection are offered:

Select:
–

All info for one element

to display all diagnostic information about an element on

one loop of an LSN module.

–

Info for element group

to display particular diagnostic information about several

elements of the selected LSN module.

–

Info for all elements on the module

to display particular diagnostic information

about all LSN elements of the selected LSN module.

The subsequent procedure for all three selection possibilities will be presented by means
of an example. The other two possibilities deviate only slightly from this.

Example:

Select

Info for element group

A list of the elements of the selected LSN module is displayed.

Select the required list fields.
The list fields are marked.

Summary of Contents for AVENAR 8000































































































Search results

Summary of Contents for AVENAR 8000

Reviews:

Related manuals for AVENAR 8000

Brands by name

Popular brands

Bosch AVENAR 8000, User Manual

Search results

Summary of Contents for AVENAR 8000

Reviews:

Related manuals for AVENAR 8000

Brands by name

Popular brands