BOS Suspension IDYLLE 2014 Service Manual Download

Page: 8 / 51

SM_150707_A

Service Manual IDYLLE since year 2014

BOS Suspension Service

4.1

SAFETY

While working on BOS suspension please wear appropriate safety equipment’s as apron, safety gloves and glasses.

When manipulating suspension oil, please wear nitrile gloves and glasses.

4.2

CLEANLINESS

When servicing your BOS suspension, be sure that you are working in conditions that will not affect the performance:

•

Work in dust free environment

•

Work on clean and organized workstation

•

Use aluminum soft jaws to protect the equipment when using a vice

•

Do not scratch any of the surface when using tools

•

Clean elements when your disassemble them

•

Drop sub-assemblies on your station in order to easily find how to reassemble them together

•

Wear long sleeves is recommended or shaved arms

If you are servicing your BOS suspension outside a workshop, you should have at least:

•

Avoid dust and air flow around your working area

•

A clean tarpaulin to place underneath the suspension on the floor

•

A bicycle repair stand to lock and maintain the suspension

•

An oil pan

•

All necessary tools listed below

Summary of Contents for IDYLLE 2014




















































Search results

Summary of Contents for IDYLLE 2014

Reviews:

Related manuals for IDYLLE 2014

Brands by name

Popular brands

BOS Suspension IDYLLE 2014, Service Manual

Search results

Summary of Contents for IDYLLE 2014

Reviews:

Related manuals for IDYLLE 2014

Brands by name

Popular brands