BOS Suspension IDYLLE 2014 Service Manual Download | Manualshive

Page: 35 / 51

background image

33

SM_150707_A

Service Manual IDYLLE since year 2014

10

11

12

Screw by hand the oil cartridge cap until the stop.
Compress and release slowly the fork 4-5 times.

Tool(s) required :

-

n/a (by hand)

Check oil level according to column “Oil level” from Fluid table, page 9 of this
document.
Take the oil level gauge.
Use a reglet to set the oil level as the distance between the stop and the end of
the tube.
Mount the oil level gauge on the syringe.

Tool(s) required :

-

Oil level gauge / ref. 150707-SEO-002

-

Syringe

-

Reglet

Unscrew the oil cartridge cap.
Compress the fork at its maximum and pull the cartridge.
Place the s oil gauge on the fork.
Aspirate oil with the syringe until air bubbles appears (you may add some oil if
only air is coming in the syringe).

Tool(s) required :

-

Oil level gauge / ref. 150707-SEO-002

-

Syringe

CAUTION

Oil level is always done suspension compressed and cartridge extended

1

2

Oil level

1

2

INFORMATION

To facilitate, put the rebound setting at 2 clics from closed.

«
...
33
34
35
36
37
...
»

Summary of Contents for IDYLLE 2014




















































Reviews:

No comments

Related manuals for IDYLLE 2014

Brand: Daga Pages: 28

Brand: JANE Pages: 6

TENSIONED CONTOUR ELECTROL

Brand: Da-Lite Pages: 8

Brand: Dacor Pages: 4

Brand: SALSA Pages: 2

BEA LZR-WIDESCAN

Brand: Halma Pages: 12

Brand: Baghera Pages: 4

My first Walker

Brand: Jamara Pages: 4

Brand: Jalousie-Welt Pages: 20

Brand: Valor Pages: 72

FRONT HEADLIGHT LENS COVER

Brand: Bimmer Jakes Pages: 4

Brand: Obelink Pages: 2

Retrotech RTX-68D-CHG

Brand: Dakota Digital Pages: 4

Brand: Axxess Pages: 8

Brand: Ikelite Pages: 32

Isolette 8000 plus

Brand: Dräger Pages: 30

Brand: EINHELL Pages: 130

Brand: IFM Electronic Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands