BOS Suspension IDYLLE 2014 Service Manual Download | Manualshive

Page: 13 / 51

background image

11

SM_150707_A

Service Manual IDYLLE since year 2014

5

Operations Summary

5.1

STEP BY STEP CHART

For all BOS suspension’s service, the following chart is followed:

1.

Receive the suspension

a.

Fill the traveler included in this manual page 10

b.

Attribute a shop order #, apply this # on the traveler and on the suspension thanks to a tape

2.

Control the suspension

a.

Oil leakages

b.

General condition (scratches, damages…)

c.

Establish a potential quotation for repairing the suspension

d.

Check settings consistency

3.

Clean the suspension. There is multiple way to clean:

a.

Pressure washing

b.

Hot water + soap

c.

Oil bath + brush

d.

Alcohol spray

4.

Note the customer’s settings of the suspension. You could use page 10 of this manual to do so.

5.

Disassemble the suspension following the §6 – Step by Step

6.

Clean the sub-assemblies and control them when removing from the suspension

7.

Change parts, reassemble and control the suspension

8.

Apply back the suspension’s settings.

9.

Clean the suspension before packaging

10.

Complete traveler with all information and join it with the suspension

5.2

HOW TO USE THIS DOCUMENT?

Step number in the routine

Color code referring to
service type (see page 8)

Localization of the step on
the suspension

Additional Caution or
Information linked to the step

Tool(s) required for the step

Pictures describing the steps

«
...
11
12
13
14
15
...
»

Summary of Contents for IDYLLE 2014




















































Reviews:

No comments

Related manuals for IDYLLE 2014

Brand: Darfon Pages: 28

Brand: VanEssa mobilcamping Pages: 8

CYCLO 315 Series

Brand: Magellan Pages: 39

Brand: MadStad Engineering Pages: 2

Brand: Raven Pages: 70

Brand: Trace2O Pages: 9

Brand: IAG Pages: 3

Brand: Ikelite Pages: 2

Brand: Acebil Pages: 11

Brand: R&G Pages: 4

EXP-MS-N4X-AT-HV-V5

Brand: Larson Electronics Pages: 5

Brand: IFM Pages: 33

Brand: Phonocar Pages: 2

Efector200 OJ51 Series

Brand: IFM Pages: 8

Brand: babyplus Pages: 36

Brand: Globalsat Pages: 2

TRANCE X ADVANCED SL 0

Brand: Giant Pages: 1

Brand: Soluna Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands