BOS Suspension IDYLLE 2014 Service Manual Download | Manualshive

Page: 37 / 51

background image

35

SM_150707_A

Service Manual IDYLLE since year 2014

16

17

18

Take off the oil level gauge from the syringe.
Fill the syringe with Y ml* of oil (see Fluid table, page 9 of this document).
Place the fork horizontally.
Empty the oil from the syringe into the air fork leg for lubrication.

* Refers to “Oil quantity left air” column in Fluid table, page 9 of this document.
** Refers to “Oil” column in Fluid table, page 9 of this document.

Tool(s) required :

-

Syringe

-

Oil **

Push the air cartridge to see the shaft threads out from the casting.
Screw the nut on the shaft with a torque 5mm HEX socket.

Tool(s) required :

-

Torque wrench

-

21mm socket

Torque = 10Nm

Place back the inferior crown:

-

Insert the crown on the stanchion

-

Measure the height from the top of the stanchion to the crown

-

Tighten the screw at torque

Place back the bumpers if present at the disassembling step.

Tool(s) required :

-

4mm HEX wrench

-

Torque wrench

Torque = 3Nm

CAUTION

Keep the suspension horizontal until the air cartridge bolt has not been tighten.

CAUTION

Keep the suspension horizontal until the air cartridge bolt has not been tighten.

1

2

1

2

3

4

«
...
35
36
37
38
39
...
»

Summary of Contents for IDYLLE 2014




















































Reviews:

No comments

Related manuals for IDYLLE 2014

Brand: Zell Pages: 33

Brand: omnicharge Pages: 12

Brand: omnicharge Pages: 72

Brand: DataSafe Pages: 4

DeltaSphere-3000

Brand: 3rdTech Pages: 9

Watchdog Super Elite

Brand: 4B Pages: 76

mamaRoo 4M-005-00

Brand: 4 Moms Pages: 17

Brand: Barco Pages: 2

Brand: Barco Pages: 22

Brand: Barco Pages: 25

Brand: Barco Pages: 16

Brand: Hama Pages: 10

Brand: Napoleon Pages: 2

Brand: Nautronic Pages: 7

Brand: NAPCO Pages: 16

Brand: Sami Pages: 10

Brand: Parrot Pages: 19

Brand: Parrot Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands