Bolin Technology DANTE AV D Series User Manual Download | Manualshive

Page: 16 / 47

background image

16

■

Multicast Transmit Flows

: The area on the right pane of the tab shows the multicast transmit flows

that have been configured on the device.

Multicast flows are listed in ID order, including the channels contained within the flow.

Note:

Unicast flow details are displayed in the Flow Information dialog.

Changing Tx channel Names

To change a Tx channel name double click on the name and type in a new one. Tx channel names must

be unique for the device.

Status Tab

The Status tab is used to obtain current information about a Dante device

Status Tab with Bolin Dante AV camera

Status Tab with Bolin Dante AV decoder

«
...
14
15
16
17
18
...
»

Summary of Contents for DANTE AV D Series
















































Reviews:

No comments

Related manuals for DANTE AV D Series

Brand: FED Pages: 12

Brand: CAMERA LINK Pages: 109

Brand: Olympus Pages: 61

Brand: Olympus Pages: 2

Brand: Okina USA Pages: 3

Brand: Okina USA Pages: 16

Brand: Vigilate Pages: 2

Brand: eSYNiC Pages: 5

Brand: Hama Pages: 2

Toy Story DJ016TS

Brand: LEXIBOOK Pages: 48

Basler scout scA640-70gc

Brand: Basler Vision Technologies Pages: 20

Brand: Polaroid Pages: 16

CUTE 4K AI 2021

Brand: LAIA Pages: 21

Infinity Zoom 210

Brand: Olympus Pages: 50

Brand: Wansview Pages: 51

Brand: Dahua Pages: 32

Brand: Tactacam Pages: 19

Brand: Elmo Pages: 95

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands