BMW R 1100 S Repair Manual Download Page 5

Page: 5 / 311

UX-VS-2, 04.00

Printed in Germany

Customer

Licence plate No.

Order No.

Mechanic’s signature

BMW
Pre-delivery check

Check the shipping crate for damage

Motorcycle:

–

unpack

–

install remaining items

–

inspect for damage

–

check that delivery is complete:

tools
documentation
keys
correct optional extras

Fill and charge the battery (mark with charging date)

Check engine oil level when cold; add oil if necessary

Check headlight beam angle, adjust if necessary

Check security of rear wheel studs
(comply with correct tightening torque)

Check tyre pressures

Fill fuel tank

Final inspection as functional check:

–

Clutch, gear shift

–

Front and rear brakes

–

Lights and signalling equipment, telltale and warning lights, instruments

–

Check operation of optional extras, ABS

–

If necessary, test ride

Confirm pre-delivery check in Service and Technical Booklet

Final cleaning

Motorcycle handed over on:

BMW Motorrad
Pre-delivery check
R 1100 S / R 850/1200 C / R 1150 GS

Summary of Contents for R 1100 S
























































































































































































































































































































Search results

Summary of Contents for R 1100 S

Reviews:

Brands by name

Popular brands

BMW R 1100 S, Repair Manual

Search results

Summary of Contents for R 1100 S

Reviews:

Brands by name

Popular brands