manualshive.com logo in svg

BMW R 1100 S, Repair Manual

Share
Download
BMW R 1100 S Repair Manual Download Page 35

00.27

Replacing Poly-V belt 

(Inspection III)
(every 60,000 km/36,000 miles)

•

If necessary, disengage fuel tank and pull to the 
rear.

•

Remove cover to expose spark plug caps.

•

Pull off spark plug caps with special puller, 

BMW No. 12 3 520

.

•

Remove spark plugs with the spark plug wrench, 

BMW No. 12 3 510

.

•

Remove front cover.

•

Slacken alternator mounting screws and nuts 
(1,3,4) and install a new Poly-V belt if necessary.

Poly-V belt adjusting procedure:
Poly-V belt installation procedure:

•

Place the Poly-V belt in position, tension it and 
turn the engine over once, then relieve belt ten-
sion.

Poly-V belt tensioning procedure:

1. Slightly tighten hex nut (1) on adjusting screw (2) 

by hand (

do not use tools

).

2. Tighten adjusting screw (2) with a torque wrench 

and keep preload applied.

3. Tighten upper retaining nut (3), then remove 

torque wrench from adjusting screw.

4. Tighten all screws and nuts. 

Tightening torque:

Poly-V belt preload......................................... 8 Nm
Alternator
to alternator support cover ........................... 20 Nm

R21000190

12 3 520

12 3 510

RS110490

RS110480

1

2

3

4

Summary of Contents for R 1100 S
























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands