manualshive.com logo in svg

BMW R 1100 S, Repair Manual

Share
Download
BMW R 1100 S Repair Manual Download Page 189

31.11

Removing and installing leading link

•

Disengage spring strut at bottom.

•

Heat ball joint mount (1) at leading link to max. 
120 °C (248 °F) and remove it.

•

Remove covers (2) from leading link pivots.

•

Disconnect the left air intake pipe from the cylin-
der head.

•

Remove left screw cap (3).

•

Remove right retaining ring (4) and retaining cap (5).

•

Remove right screw (6) and remove shaft (7) by 
pulling to the left.

•

Pull telescopic fork forwards and carefully re-
move leading link by pulling forwards.

e

 Caution:

Protect parts against scratching; mask off if necessary.

•

Installation is the reverse of the removal proce-
dure.

•

Apply a light coating of grease to the shaft before 
installing.

•

Tighten the ball joint in the leading link using 
socket, 

BMW No. 31 5 601

, and Allen key, 

BMW No. 31 5 603

.

X 

Tightening torque:

Leading link to engine on right ..................... 73 Nm
Left screw cap (coat 
thread lightly with Never Seeze).................... 42 Nm
Leading link to ball joint
(use a new nut 
or clean  Loctite 2701) .................. 130 Nm
Spring strut to leading link............................ 50 Nm

Disassembling/assembling leading 
link

•

Press the bearing out/in with a suitable tool.

e

 Caution:

Always install bearing by applying pressure to outer 
race.

Removing and installing front spring 
strut

X 

Tightening torque:

Spring strut to frame .................................... 43 Nm
Spring strut to leading link............................ 50 Nm

R21310060

1

2 4

5

6

7

3

2

31 5 601

31 5 603

Summary of Contents for R 1100 S
























































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands