BMW R 1100 S Repair Manual Download Page 130

Page: 130 / 311

13.7

Removing and installing throttle-
valve potentiometer

•

Press in spring keeper of multi-pin plug for throt-
tle-valve potentiometer (1) and disconnect plug.

Note:

Do not remove throttle-valve potentiometer unless
due for replacement (basic setting is necessary —
see Motronic diagnosis instructions).

•

Remove the throttle-valve potentiometer.

•

Adjust throttle-valve potentiometer with

BMW

MoDiTeC

after installing.

•

Mark screws with a paint spot.

Removing and installing Motronic
control unit

•

Remove fuel tank.

Caution:

Switch off ignition; disconnect earth (ground) lead
from battery and insulate it.

•

Disconnect plug from Hall sensor.

•

Remove Motronic control unit.

•

Remove connector strip.

•

Installation is the reverse of the removal proce-
dure.

•

Switch on the ignition.

•

Without starting the engine, fully open the throttle
once or twice so that the Motronic control unit
can register the throttle-valve positions.

Note:

Disconnecting the battery deletes all entries (e.g.
faults, settings) stored in the Motronic control unit’s
memory.
Loss of settings can temporarily impair the operat-
ing characteristics when the engine is restarted.

RS130010

Summary of Contents for R 1100 S
























































































































































































































































































































Search results

Summary of Contents for R 1100 S

Reviews:

Brands by name

Popular brands

BMW R 1100 S, Repair Manual

Search results

Summary of Contents for R 1100 S

Reviews:

Brands by name

Popular brands