BMW R 1100 S Repair Manual Download Page 227

Page: 227 / 311

34.5

Disassembling and assembling front
brake caliper

Caution:

not separate

the brake caliper halves!

•

Remove the brake caliper.

•

Remove keeper from retaining pin (1).

•

Drive out the retaining pin (1) from the wheel side.

•

Remove brake pads by pulling downwards.

•

Close the bleed screw.

Tightening torque:

Bleed screw in brake caliper ........................ 14 Nm

•

Secure two opposing brake pistons with reset-
ting tool,

BMW No. 34 1 500

•

Place a cloth between the other pair of pistons.

Caution:

Do not insert your fingers between the pistons; risk
of injury

•

Carefully

press out brake pistons (2), using a

compressed air gun at the brake line connection.

•

Remove the two sealing rings (3,4) from the left
and right brake cylinder bores.

•

Inspect the brake caliper piston for hairline
cracks, score-marks and other damage.

•

Coat new sealing rings (3,4) with brake fluid and
install.

Caution:

Keep the brake pistons parallel with their bores
when installing.

•

Coat brake caliper pistons (2) with brake fluid
and insert.

•

Remove and install the other two brake pistons
in the same way.

•

Using piston compressor (7),

BMW No. 34 1 500

, if necessary press the pis-

tons fully back.

•

Install the brake pads.

34 1 500

RS340070

Summary of Contents for R 1100 S
























































































































































































































































































































Search results

Summary of Contents for R 1100 S

Reviews:

Brands by name

Popular brands

BMW R 1100 S, Repair Manual

Search results

Summary of Contents for R 1100 S

Reviews:

Brands by name

Popular brands