background image

24

10. ONE YEAR LIMITED WARRANTY

This product is warranted to the original purchaser to be free from defects in material or workmanship 
for a period of one (1) year from the date of the original retail purchase.
This warranty does not cover defects or damage due to improper installation, alteration, accident or 
any other event beyond the control of the manufacturer. Defects or damage resulting from misuse, 
abuse, or negligence will void this warranty. This warranty does not cover scratching or damage that 
may result from normal usage.

This product is not intended for institutional or commercial use; the manufacturer does not assume 

any liability for such use. Institutional or commercial use will void this warranty.
This warranty is nontransferable and is expressly limited to the repair or replacement of the defective 
product. During the warranty period, the manufacturer shall repair or replace defective parts at no 
cost to the purchaser. Shipping charges and insurance are not covered and are the responsibility of 
the purchaser. Labor charges and related expenses for removal, installation, or replacement of the 
product or components are not covered under this warranty.

The manufacturer reserves the right to make substitutions to warranty claims if parts are unavailable 
or obsolete.

The manufacturer shall not be liable for loss of use of the product or other consequential or incidental 
costs, expenses or damages incurred by the consumer of any other use. The user assumes all risk of 
injury resulting from the use of this product.

This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties 

of merchantability or fitness for use to the extent permitted by Federal or state law. Neither the 

manufacturer nor any of its representatives assumes any other liability in connection with this product.

All warranty claims must include the retailer’s information where the product was originally 
purchased. A purchase receipt or other proof of date of purchase will be required to process all 
warranty claims. The model number and part numbers found within the assembly instructions 
will be required when submitting any parts requests or warranty claims.

For further warranty information or inquiries, please call 

1 (800) 759-0977

Blue Wave Products, Inc. 

101 N Raddant Drive

Batavia, IL 60510

Summary of Contents for FLOWXTREME PRO VS II

























Reviews: