background image

6

1. SAFETY INSTRUCTIONS (CONTINUED)

Hazardous Pressure.

Pool water circulation systems operate under hazardous pressure during 
start-up, normal operation, and after pump shut-off. Stand clear of circulation 
system equipment during pump start-up. Failure to follow safety and operation 
instructions could result in violent separation of the pump housing and cover 
due to pressure in the system, which could cause property damage, severe 
personal injury, or death. Before servicing the pool water circulation system, 

all system and pump controls must be in the off position. The filter manual air 
relief valve must be in the open position if it is part of the filtration system. 

Before starting system pump, all system valves must be set in a position to 

allow system water to return back to the pool. Do not change filter control valve 

position while system pump is running. Before starting system pump, fully open 

filter manual air relief valve. Do not close filter manual air relief valve until a 

steady stream of water (not air or air and water) is discharged. All suction and 
discharge valves 

MUST

 be 

OPEN

 when starting the circulation system.

Failure to do so could result in severe personal injury and/or property damage.

WARNING

Separation Hazard.

Failure to follow safety and operation instructions could result in violent 
separation of pump components. Strainer cover must be properly secured to 
pump housing with strainer cover lock ring. Before servicing the pool and spa 
circulation system, all system and pump controls must be in the off position and 

the filter manual air relief valve must be in the open position. Do not operate 

pool circulation system if a system component is not assembled properly, 

damaged, or missing. Do not operate pool circulation system unless filter air 

relief valve body is in closed position. All suction and discharge valves 

MUST

 be

 

OPEN

 when starting the circulation system.

Failure to do so could result in severe personal injury and/or property damage.

WARNING

WARNING

NEVER 

operate or test the circulation system at more than 

40 PSI.

Summary of Contents for FLOWXTREME PRO VS II

























Reviews: