background image

4

1. SAFETY INSTRUCTIONS (CONTINUED)

WARNING

Some pump

 components have a finite life. All components should be inspected 

frequently and replaced if found to be worn, damaged, broken, cracked, or 
missing.

Risk of Electric Shock

.

Hazardous voltage. Can shock, burn, or cause death. To reduce the risk of 
electric shock, do NOT use an extension cord to connect unit to electric supply. 
Provide a properly located outlet. It is required that licensed electricians do all 
electrical wiring. All electrical wiring MUST be in conformance with applicable 
local and national codes and regulations. Before working on pump or motor, 
disconnect motor wiring.

WARNING

WARNING

Do NOT bury cord. Place the cord on the ground so it can avoid abuse from 
lawn mowers, hedge trimmers and other equipment.

Connect only to a grounding type receptacle protected by a Ground Fault 
Circuit Interrupter (GFCI). Contact a licensed electrician if you cannot verify that 
the receptacle is protected by a GFCI.

Failure to bond pump to pool structure will increase risk for electrocution 
and could result in injury or death. To reduce the risk of electric shock, see 
installation instructions and consult a professional electrician on how to bond 
pump.
Also, contact a licensed electrician for information on local electrical codes 
for bonding requirements. Use a solid copper conductor, size 8 or larger. 
Run a continuous wire from external bonding lug to reinforcing rod or mesh. 
Connect a No. 8 AWG (8.4 mm2) solid copper bonding wire to the pressure wire 
connector provided on the motor housing and to all metal parts of swimming 
pool, spa, or hot tub, and to all electrical equipment, metal piping (except gas 
piping), and conduit within 5 ft. (1.5m) of inside walls of swimming pool, spa, or 
hot tub. 

IMPORTANT

 - Reference NEC codes for all wiring standards including, but not 

limited to, grounding, bonding, and other general wiring procedures. 

NOTE

 - The National Electrical Code (NEC) permits use of a cord with a 

maximum 3 ft. (1 m) length. If your pump is equipped with a cord complying 
with the NEC, the preceeding four (4) hazards apply.

WARNING

WARNING

WARNING

WARNING

Failure to install according to defined instructions may result in severe personal 

injury or death.

Use of unauthorized replacement parts voids warranty.

Summary of Contents for FLOWXTREME PRO VS II

























Reviews: