MT2136
1-5
TEMPERATURE CONTROLS
Computer solid state controls for ovens manufactured after mid sept., 1993
NOTE:
= ASAP Distributor Required Stocking Parts
Ref.
No.
Part
No.
Description
Ref.
No.
Part
No.
Description
M3149 Controller, Digital Temperature
M3439 Relay, Digital Temp. Controller,
10 AMP, 250V
M3150 Control Board, Temperature HiĆ
Lo Limit
M3151 Thermocouple, Dual Lead
M3152 Thermocouple, Single Lead
M6474 Computer Control Kit, Closed
Loop SB
FW525 Computer Control Kit, Closed
Loop SB (Reconditioned)
M5635 Computer Control Kit, Open
Loop TB
M7427 Probe, Temperature RTD, 500
OHMS
M3347 Cable, Computer Control, 25
Pin, 10 Foot
M3348 Cable, Computer Control, 9 Pin,
10 Foot
M3490 Cable, Computer Control, 25
Pin, 50 Foot
M3491 Cable, Computer Control, 9 Pin,
50 Foot
M3314 Bracket, Computer Wall
M5661 Bracket Assy., Cable Clamp
19
22672 Relay, Control (Ice Cube) (Qty 4)
18
M3295 Thermostat, High Limit (Manual
Reset)
M0152 Contact,
Emergency
Stop
Switch
M3296 Activator, Emergency Stop
Switch (Mushroom Shape)
M3297 Nameplate, Emergency Stop
20
M3136 Breaker, 7 AMP Circuit (Qty 2)
(Before AB Ver.)
21
M2772 Breaker, 4 AMP Circuit (Qty 2)
(Before AB Ver.)
26
M3352 Transformer, 120V to 24V (Qty 1)
M3349 Harness, InterĆConnecting DC
Drive, 3 Wire (For 9 Pin)
M3353 Harness, Relay Board (Open
Loop) (Qty 1) (For 25 Pin)
M7237 Harness, Relay Board (Closed
Loop) (Qty 1) (For 25 Pin)
Summary of Contents for MT2136 Series
