biochrom NanoVue Plus User Manual Download Page 70

Page: 70 / 77

5061-049 REV 1.4

8.4. After sales support

For all technical support and advice on NanoVue Plus please contact your supplier.

www.biochromspectros.com

or email at [email protected]

Support agreements that help you to fulfil the demands of regulatory guidelines

concerning GLP/GMP are available.

• Calibration, certification

• Certificated engineers and calibrated test equipment

• Approved to ISO 9001 standard

Choice of agreement apart from break down coverage can include;

• Preventative maintenance

• Certification

Accessories

Built-in Printer accessory

28918227

Spare paper for printer (20 rolls)

28918226

Bluetooth accessory

80-3003-96

Sample Plate Replacement kit

28955301

Lower Sample Plate Replacement

28937587

Pathlength Calibration Kit

80-2140-09

PVC software

28923188

SD Card Accessory

80-3005-05

Summary of Contents for NanoVue Plus














































































Search results

Summary of Contents for NanoVue Plus

Reviews:

Related manuals for NanoVue Plus

Brands by name

Popular brands

biochrom NanoVue Plus, User Manual

Search results

Summary of Contents for NanoVue Plus

Reviews:

Related manuals for NanoVue Plus

Brands by name

Popular brands