manualshive.com logo in svg

Binder TWG 01, Operating Manual, Page: 33 / 39

Share
Download
Binder TWG 01 Operating Manual Download Page 33

 

 

 

TWG 01 01/2011 

page 33/39 

 

7.4 

APT-COM™ 3 settings for remote alarm 

In APT-COM™ 3 monitoring by the monitoring software Watch Tool is activated with the button “Watch 
enable“ in the configuration menu “Watch Tool“ (see APT-COM™ 3 operating manual).  

All alarm settings need to be made in the monitoring software Watch Tool. They are extensively 
described in the APT-COM™ 3 operating manual. 

 

8. 

Operation 

8.1 

State of alert 

When all connections are established and all settings entered, the Alarm Box AB 01 is switched on and 
APT-COM™ is running with the appropriate settings for alarm operation as well as, in case of APT-
COM™ 3, the monitoring software Watch Tool (see chap. 7.3 or 7.4), the TWG 01 must be on alert. 

On alert: 

Display Signification 

Red LED lit 

Connection to power supply ok 

Yellow LED off 

Programming is complete  

Green LED lit * 

or

 

Connection to telephone line ok 

Green LED not lit * 

Connection to telephone line exists, but is inactive 
(no local loop, this may be introduced only when 
dialing) 

*   This depends on the type of telephone connection and on the local and national configuration of the 

telephone network. 

 

Not on alert: see chap. 9. 

 

8.2 

Stopping / resetting an alarm 

During and following an alarm the red LED flashes. An alarm can be stopped hitting the reset key 

. 

 

After each released alarm the TWG 01 must be made ready for alarm again. 

Hit the reset key 

 to reset the alarm and make the unit ready for alarm again. 

If there is no more alarm, the  TWG 01 is now on alert again.  

If the red LED continues to flash after reset with key 

 the alarm cause is still existent and must be 

removed first, or the alarm has not yet been reset at the APT-COM™ software. 

 

8.3 

Manual alarm / Test alarm 

You have got the possibility to release an alarm directly at the TWG 01. 

Press button 

 for 2 sec. The TWG 01 will now dial the phone numbers and transmit the alarm 

message. 

Summary of Contents for TWG 01








































Reviews:

No comments