Binder TWG 01 Operating Manual Download Page 16 | Manualshive

Page: 16 / 39

Binder TWG 01 Operating Manual Download Page 16

TWG 01 01/2011

page 16/39

5.5.2 Overview command keys

Key Function

to

Program selection, Information entry during programming (chap. 6.1.2)

Program selection for limiting the number of effective alerts (chap. 6.7)

Program selection for recording a voice message (chap. 6.3)

Starting and ending number entry for pagers (chap. 6.4.4)

Starting number entry for number of call repeats (chap. 6.4.6)

Entering the number of effective alerts (chap. 6.7)

Direct manual alarm (in emergency cases or for test purpose) (chap. 8.3)

Playback independent of dialing tone (chap. 6.4.2)

Call group (chap. 6.5, 6.6.2)

Reset of programming (chap. 9.2)

Programming

Dialing delay (chap. 6.4.3)

Program selection for number of call repeats (chap. 6.4.6)

Transfer delay for pagers (chap. 6.4.4)

Programming reset (chap. 9.2)

Entering the number of confirmation codes for all call groups (chap. 6.6.2)

Stopping / resetting an alarm (chap. 8.2)

Alarm memory deletion

Voice message recording or playback stop (chap. 6.3)

Test mode stop

6.

Programming

In this chapter all kinds of programming are described that you need to execute until your TWG 01 is
ready for operation.

6.1

General information

6.1.1 Situation following connection (chap. 5)

•

Red LED lit: Power supply is on

•

Yellow LED flashes: Messages are programmed incompletely so far

•

Green LED lit: Connection to phone line ok

or

•

Green LED not lit: Connection to phone line exists, but is inactive (no local loop, this may be

introduced only when dialing). This depends on the type of telephone connection and on the local and
national configuration of the telephone network.

«
...
14
15
16
17
18
...
»

Summary of Contents for TWG 01








































Reviews:

No comments