manualshive.com logo in svg

Binder TWG 01, Operating Manual, Page: 17 / 39

Share
Download
Binder TWG 01 Operating Manual Download Page 17

 

 

 

TWG 01 01/2011 

page 17/39 

 

6.1.2  Basic entry principle 

Hitting a key, termination of a program step and of the whole entry are confirmed by the yellow LED. Most 
of the program entries require that the program key is used three times during the procedure: 

Step Key 

Effect Yellow 

LED

 

 

1. 

 

Program call 

1x flashing 

2. 

Entry via keyboard 

Program selection 

1x flashing 

following each hit 

3. 

 

Selection of program step 

confirmed 

2x flashing 

4. 

Entry via keyboard or voice 

recording 

Information entry 

1x flashing 

following each hit 

5. 

 

Programming terminated 

lights up for 1.5 sec 

 

 

Wait for the yellow LED lighting up before pressing the next key. Pressing the next key too 
quickly may lead to errors. Mind that every programming is confirmed at the end by the 
yellow LED lighting up for 1.5 seconds. 

If you do not press any key for 10 seconds during programming, the entry will be cancelled. The yellow 
LED flashes 4 times, the previous entries will not be adopted. 

 

Avoid pausing during entry. After 10 seconds you will need to start again. 

You can cancel a started programming with button 

. 

If the red LED flashes continuously (alarm), press button 

 

and continue with the programming. 

 

6.2 

Selection of the connection type for the Alarm Box AB 01 and setting the 
alarm delay time 

The TWG 01 can react to impulses of alarm systems which are either set to “Normally open“ (N.O.) or to 
“Normally closed“ (N.C.). It can be connected to alarm systems of both types. To connect it to the 
BINDER Alarm Box AB 01 the type of alarm must be set to “Normally closed”. 

 

Connection types for the alarm system: 

  Normally open (not used)                   Normally 

closed 

 

For the direct connection to a zero-voltage relay alarm contact at a BINDER temperature chamber the 
logic of this alarm contact can be accordingly set at the TWG 01. 

The delay time for triggering an alarm can be defined. Different settings are available for the different 
activation types. Settings   and   are suitable for impulse-type activation as with sensors of magnetic 
contact, shocks, or breaking. Settings 

 or   are suitable for continuous activation by the BINDER 

Alarm Box AB 01 and serve to avoid faulty alarms. If the alarm by the Alarm Box AB 01 ends before 
rundown of the selected alarm delay time (10 or 15 sec), the dialing procedure at the TWG 01 is stopped. 
The TWG 01 is still on alert noticeable by the red LED lit. 

Summary of Contents for TWG 01








































Reviews:

No comments