manualshive.com logo in svg

Binder TWG 01, Operating Manual, Page: 10 / 39

Share
Download
Binder TWG 01 Operating Manual Download Page 10

 

 

 

TWG 01 01/2011 

page 10/39 

 

4. 

Completeness of delivery, transportation, storage, and 
installation 

4.1 

Unpacking, and checking equipment and completeness of delivery 

After unpacking, please check the unit and its optional accessories, if any, based on the delivery note for 
completeness and for transportation damage. Inform the carrier or post office/parcel service immediately 
if transportation damage has occurred.  

Scope of delivery: 

•

  Telephone dialing device TWG 01 

•

  Connection cable 2 m / 

6.6 ft

 (connection to telephone wall jack) 

•

  Operating Manual Telephone dialing device TWG 01 

•

  Power supply unit with various interchangeable plug adapters 

 

 

Plug adapter for UK 

 

 

 

Plug adapter for Australia 

 

 

 

 

Plug adapter for EU 

 

 

 

Plug adapter for the USA  

Figure 3: Delivered interchangeable plug adapters 

 

 

 

Figure 4: Power supply unit 90-264V AC / 12V DC (Art. No. 5020-0029) 

For disposal of the transport packing, see chap. 11.1. 

 

4.2 

Storage 

Intermediate storage of the unit is possible in a closed and dry room. Observe the guidelines for 
temporary decommissioning (chap. 11.2). 

•

  Permissible ambient temperature range: 0 °C / 

32 °F

 up to +40 °C / 

104 °F

. 

•

  Permissible ambient humidity: max. 80 % r.H., non-condensing 

When after storage in a cold location you transfer the unit to its warmer installation site, condensation 
may form. Before start-up, wait at least one hour until the unit has attained ambient temperature and is 
completely dry. 

Summary of Contents for TWG 01








































Reviews:

No comments