Binder TWG 01 Operating Manual Download Page 36 | Manualshive

Page: 36 / 39

Binder TWG 01 Operating Manual Download Page 36

TWG 01 01/2011

page 36/39

10.2 Service

DANGER

Electrical hazard.

Danger of death.

∅

The unit must NOT become wet during operation.

∅

NEVER open the device for repair purpose.

¾

Have all maintenance work conducted by professional electricians or experts

authorized by BINDER.

Warranty / repair and maintenance tasks must only be performed by persons or workshops
that have been authorized by BINDER. Otherwise, BINDER will perform the tasks itself. If
you do not know whom to contact in the event of a fault, contact us and we will advise you of
the nearest authorized workshop.

Never try to open the device in order to repair it. In case of problems please contact BINDER Service:

BINDER telephone hotline:

+49 (0) 7462 2005 555

BINDER fax hotline:

+49 (0) 7462 2005 93555

BINDER e-mail hotline:

[email protected]

BINDER service hotline USA:

+1 866 885 9794 or +1 631 224 4340 (toll-free in the USA)

BINDER service hotline Spain

+34 9492 677 23

BINDER service hotline Asia Pacific:

+852 39070500 or +852 39070503

BINDER service hotline Russia and CIS

+7 495 98815 17

BINDER Internet website

http://www.binder-world.com

BINDER address

BINDER GmbH, post office box 102, D-78502 Tuttlingen

International customers, please contact your local BINDER distributor.

11. Disposal

11.1 Disposal of the transport packing

Packing element

Material

Disposal

Shipping box

Cardboard

Paper recycling

Foamed plastic stuffing

PE foam

Plastic recycling

Bag for operating manual

PE foil

Plastic recycling

Insulating air cushion foil

PE foil

Plastic recycling

If recycling is impossible, all packing parts can also be disposed of with normal waste.

11.2 Decommissioning

Disconnect the device from the power supply.

•

Temporary decommissioning: See indications for appropriate storage, chap. 4.2.

•

Final decommissioning: Dispose of the unit as described in chap. 11.3 to 11.5.

«
...
34
35
36
37
38
...
»

Summary of Contents for TWG 01








































Reviews:

No comments