Billion BiPAC 8700VAX(L)-1600, User Manual

Page: 130 / 327

125
802.11n Rate:
This allows you to select the fixed transmission rate or auto.
802.11n Protection:
turn off for maximize throughput.
Support 802.11n Client Only:
turn on the option to only provide wireless access to the clients
operating at 802.11n speeds.
RIFS Advertisement:
Reduced Inter-frame Spacing (RIFS) is an 802.11n feature that also improves
performance by reducing the amount of dead time required between OFDM transmissions. Select
Off to disable this function or auto to enable this function.
OBSS Co-Existence:
coexistence (or not) between 20 MHZ and 40 MHZ overlapping basic service
sets (OBSS) in wireless local area networks.
RX Chain Power Save:
Enabling this feature turns off one of the Receive chains, going from 2x2 to
2x1 to save power.
RX Chain Power Save Quiet Time:
The number of seconds the traffic must be below the PPS
value before the Rx Chain Power Save feature activates itself.
RX Chain Power Save PPS:
The maximum number of packets per seconds that can be processed
by the WLAN interface for duration of Quiet Time, described above, before the Rx Chain Power
Save feature activates itself.
54g™ Rate:
Available after changing
802.11n Rate
to “Use 54g Rate” in
802.11n Rate
. It is used to
limit 11n speed to a specific rate, e.g. 6M, 12M, 24M, 48, etc.
Multicast Rate:
Setting for multicast packets transmission rate.
Basic Rate:
Setting for basic transmission rate. It is not a specific kind of rate but a series of rates
supported. When set to Default, the router can transmit with all kinds of standardized rates.
Fragmentation Threshold:
A threshold (in bytes) whether the packets will be fragmented and at
what size. Packets succeeding the fragmentation threshold of 802.11n WLAN will be split into
smaller units suitable for circuit size. While the packets smaller than fragmentation threshold will not
be fragmented. Default is 2346, setting the fragmentation too low may result in poor performance.
RTS Threshold:
Request to Send (RTS) threshold specifies the packet size, when exceeds the size,
the RTS/CTS will be triggered. The default setting of 2347(max length) will disable the RTS.
DTIM Interval:
Delivery Traffic Indication Message (DTIM). The entry range is a value between 1
and 255. A DTIM is countdown variable that informs clients of the next window for listening to
broadcast and multicast messages. When the AP has buffered broadcast or multicast messages for
associated clients, it sends the next DTIM with a DTIM interval value. AP clients hear the beacons
and awaken to receive the broadcast and multicast messages. The default is 1.
Beacon Interval:
The amount of time between beacon transmissions in is milliseconds. The default
is 100ms and the acceptable is 1- 65535. The beacon transmissions identify the presence of an
access point.
Global Max Clients:
Here you have the option of setting the limit of the number of clients who can
connect to your wireless network.
XPress™ Technology:
It has been designed to improve the wireless network efficiency. Default is
disabled.
Regulatory Mode:
Select to deny any regulatory mode, which is only for
5GHz
band wireless.
There are two regulatory modes:
Configuring Your Router Wireless 5G(wl0) & 2.4G(wl1) –
Advanced for 5G Wireless
802.11h: The standard solves interference problems with e.g. satellites and radar using the same
5 GHz band as 802.11a or 802.11n dual-band access points.
802.11d: This standard automatically adjusts its allowed frequencies, power levels and bandwidth
accordingly to the country it's located in.
Pre-Network Radar Check (Used for 802.11h only):
Specifies a period of time in seconds [0-99] to