![background image](http://html.mh-extra.com/html/benq/sx930/sx930_service-manual_2735009020.webp)
20
(b)MHL mode:
-Support LPCM, two audio channels (follow IEC 60958 and IEC 61937)
-Support audio sampling rate : 32kHz, 44.1kHz, 48kHz
- Support audio bit rate : 16 bits, 20 bits, 24 bits
(C) DVI Mode:
Analog audio is supported through PC audio input terminal.
Note. There timing showing depend the EDID file and VGA graphic card limitation.
It is possible that user cannot choose the above timings on VGA display card.
1.1.6 PC Input
(1) Pin definition and Signal Level:
Pin
Signal
Parameter
Min
Type
Max
1
RDATA
GDATA
BDATA
Impedance
75
Ohm
2
Amplitude
0.7
Volts peak-to-peak
3
Black pedestal
0
Volts
Pixel Clock
170
M Hz
2
GDATA_SOG
Impedance
75
Ohm
Amplitude
1
Volts peak-to-peak
Video amplitude
0.7
Volts peak-to-peak
Sync amplitude
0.3
Volts peak-to-peak
Black pedestal
0
Volts
Pixel Clock
170
M Hz
13
HDATA
Impedance
1
K ohm
Amplitude, low level
0
0.5
volt
Amplitude, high level
2.5
5
Volt
Frequency
31
102
K Hz
14
VDATA
Impedance
1
K ohm
Amplitude, low level
0
0.8
volt
Amplitude, high level
2.5
5
Volt
Frequency
48
120
Hz
12
SDADATA
Amplitude, low level
0
0.8
volt
Amplitude, high level
2.5
5
Volt
15
SCLDATA
Amplitude, low level
0
0.8
volt
Amplitude, high level
2.5
5
Volt
4
NC
5
NC
6
Red GND
7
Green GND
8
Blue GND
9
DDCP 5V
5
Volts
10
Sync. Return
11
GND
2
G DATA
Share with Y
Amplitude (with sync)
1
Volts peak to peak
Impedance
75
ohm
1
R DATA
Share with Pr
Amplitude
0.7
Volts peak to peak
Impedance
75
ohm
3
B DATA
Share with Pb
Amplitude
0.7
Volts peak to peak
Impedance
75
ohm
Summary of Contents for SX930
