151
2. RS-232 Command Code
For all application
Condition
1.
Character delay=>0 ms
2.
Stand by 0.5W and any baud rate don’t loss command.
3.
Test with Source in and no source
4.
Test with Crestron control
5.
Support volume bar display for volume command
6.
Support Lan over Rs232 (no <CR> limitation)
7.
Each input upper case and lower case character should be action)
(The response string will be in upper case)
(Version 13.5)
Function
Type
Operation
ASCII
Support
Power
Write
Power On
<CR>*pow=on#<CR>
Y
Write
Power off
<CR>*pow=off#<CR>
Y
Read
Power Status
<CR>*pow=?#<CR>
Y
Source
Selection
Write
COMPUTER/YPbPr
<CR>*sour=RGB#<CR>
Y
Write
COMPUTER 2/YPbPr2
<CR>*sour=RGB2#<CR>
N
Write
COMPUTER 3/YPbPr3
<CR>*sour=RGB3#<CR>
N
Write
Component
<CR>*sour=ypbr#<CR>
Y
Write
Component2
<CR>*sour=ypbr2#<CR>
N
Write
DVI-A
<CR>*sour=dviA#<CR>
N
Write
DVI-D
<CR>*sour=dvid#<CR>
N
Write
HDMI/MHL
<CR>*sour=hdmi#<CR>
Y
Write
HDMI 2/MHL2
<CR>*sour=hdmi2#<CR>
Y
Write
Composite
<CR>*sour=vid#<CR>
Y
Write
S-Video
<CR>*sour=svid#<CR>
Y
Write
Network
<CR>*sour=network#<CR>
N
Write
USB Display
<CR>*sour=usbdisplay#<CR>
N
Write
USB Reader
<CR>*sour=usbreader#<CR>
N
Write
Wireless
<CR>*sour=wireless#<CR>
N
Write
HDbaseT
<CR>*sour=hdbaset#<CR>
N
Write
DisplayPort
<CR>*sour=dp#<CR>
N
Read
Current source
<CR>*sour=?#<CR>
Y
Audio Control
Write
Mute On
<CR>*mute=on#<CR>
Y
Write
Mute Off
<CR>*mute=off#<CR>
Y
Read
Mute Status
<CR>*mute=?#<CR>
Y
Write
<CR>*vol=+#<CR>
Y
Write
Volume -
<CR>*vol=-#<CR>
Y
Read
Volume Status
<CR>*vol=?#<CR>
Y
Write
Mic.
<CR>*#<CR>
N
Write
Mic. Volume -
<CR>*micvol=-#<CR>
N
Read
Mic. Volume Status
<CR>*micvol=?#<CR>
N
Audio source
select
Write
Audio pass Through off
<CR>*audiosour=off#<CR>
Y
Write
Audio-Computer1
<CR>*audiosour=RGB#<CR>
Y
Write
Audio-Computer2
<CR>*audiosour=RGB2#<CR>
N
Write
Audio-Video/S-Video
<CR>*audiosour=vid#<CR>
Y
Write
Audio-Component
<CR>*audiosour=ypbr#<CR>
N
Write
Audio-HDMI
<CR>*audiosour=hdmi#<CR>
Y
Write
Audio-HDMI2
<CR>*audiosour=hdmi2#<CR>
Y
Read
Audio pass Status
<CR>*audiosour=?#<CR>
Y
Picture Mode
Write
Dynamic
<CR>*appmod=dynamic#<CR>
N
Write
Presentation
<CR>*appmod=preset#<CR>
Y
Write
sRGB
<CR>*appmod=srgb#<CR>
Y
Write
Bright
<CR>*appmod=bright#<CR>
Y
Summary of Contents for SX930
