background image

 

RBJ Series of Rolling Jacks 

3

 

P/N 5900004 — Rev. D1 — October 2020 

Table of Contents 

 

Introduction  

 3

 

Operation  

 19

 

 

Shipping Information  

 4 

Maintenance  

 23

 

 

Safety Considerations  

 4 

Troubleshooting  

 24

 

 

Components  

 6 

Accessories  

 25

 

 

FAQ  

 8

 

Labels  

 26

 

 

Specifications  

 9

 

Parts Sheets  

 27

 

 

Setup  

 10

 

Introduction 

This manual covers the RBJ Series of Rolling Bridge Jacks, which are used on four-post Lifts to raise 

two or four wheels off the Runway of the Lift, making automotive service such as brake jobs and 

suspension work easier to accomplish. 
This manual covers the following RBJ models: 

 

RBJ15000

: Raises up to 15,000 lbs / 6,804 kg. For BendPak HDS-27 and HDS-27X Lifts. 

 

RBJ18000

: Raises up to 18,000 lbs / 8,165 kg. For BendPak HDS-35 and HDS-35X Lifts. 

 

RBJ25000

: Raises up to 25,000 lbs / 11,340 kg. For BendPak HDS-40 and HDS-40X Lifts. 

BendPak also makes Rolling Jacks with 4,500, 6,000, 7,000, and 9,000 pound capacities; those 

models are covered in a 

separate manual available on the BendPak website

. 

This manual is mandatory reading for all users of these Rolling Bridge Jacks, including anyone who 

installs, operates, maintains, or repairs them. 

 DANGER

 

Be very careful when installing, operating, maintaining, or repairing your unit; failure 
to do so could result in property damage, product damage, injury, or (in very rare 

cases) death. Make sure only authorized personnel operate the unit. All repairs 

must be performed by an authorized technician. Do not make modifications to the 
unit; this voids the warranty and increases the chances of injury or property 

damage. Make sure to read and follow the instructions on the labels on the unit. 

Keep this manual on or near the equipment so that anyone who uses or services it can read it. 
If you are having issues, refer to the 

Troubleshooting

 section of this manual for assistance. 

Technical support and service is available from your dealer, on the Web at 

bendpak.com/support

by email at 

[email protected]

, or by phone at 

(800) 253-2363

, extension 196. 

You may also contact BendPak for parts replacement information (please have the model and serial 
number of your unit available) at 

(800) 253-2363

, extension 191. 

Summary of Contents for RBJ15000

































Reviews: