background image

1

   INSTALLATION AND OPERATION MANUAL

1645 Lemonwood Dr.

Santa Paula, CA. 93060,  USA

Toll Free 1-888-262-3880

Tel: 1-805-421-5114

www.quickjack.com

IMPORTANT SAFETY INSTRUCTIONS 

SAVE THESE INSTRUCTIONS

PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO 
INSTALLATION AND OPERATION. BY PROCEEDING WITH JACK 
INSTALLATION AND OPERATION YOU AGREE THAT YOU FULLY 
UNDERSTAND AND  COMPREHEND THE FULL CONTENTS OF THIS 
MANUAL. FORWARD THIS MANUAL TO ALL OPERATORS. FAILURE TO 
OPERATE THIS EQUIPMENT AS DIRECTED MAY CAUSE INJURY OR DEATH. 

MAN REV D  07-22-2015

P/N 5900395

3,500 / 5,000 POUND CAPACITY

QUICKJACK

MODELS:

BL-3500      

VER B

BL-5000        

VER B

BL-5000XL    

VER B

BE SAFE

Your new jack was designed and built with safety in mind. 

However, your overall safety can be increased with proper 

training and thoughtful operation on the part of the operator. 

DO NOT

 operate or repair this equipment without reading 

this manual and the important safety instructions shown 

inside.  Keep this operation manual near the jack at all 

times. Make sure that ALL USERS read and understand 

this manual.

RECEIVING

The shipment should be thoroughly inspected as soon as it 

is received.  The signed Bill of Lading is acknowledgement 

by the shipping carrier as receipt of this product as listed 

in your invoice as being in a good condition of shipment.  If 

any of these goods listed on this Bill of Lading are missing 

or damaged, do not accept goods until the shipping carrier 

makes a notation on the freight bill of the missing or dam-

aged goods.  Do this for your own protection.

QUICKJACK

By Ranger Products

WARNING

!

PATENTED.  ALL RIGHTS RESERVED   

Summary of Contents for BL-3500

































Reviews: