Belanger SUDZAMELEON ARCH Owner'S Manual Download Page 68

Page: 68 / 88

SUDZAMELEON

ARCH

Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

1MANUL956

Maintenance

Replacement Parts

Wall Washers: 111108

(includes two of the RGB LED Wall Washer Assemblies shown below)

111109 RGB LED Wall Washer

Assembly includes:

1LED-WW025

1ELECT-FS110
1ELECT-FS135 (2)

1ELECT-FS136 (2)
SHRINK TUBE 1” GSHS-1625W-3/8” Black

1LED-WW025

1WASHR-LC125 (2)

1ELECT-FS177

1ELECT-FS775

1WASHR522

111110

1FSTNR-HH145 (2)

1WASHR-FL332 (2)

Assembly Information

All parts in this assembly ship attached to the Air

Plenum except 111109 and cable 11110. The LED is

to be attached to the Air Plenum at the site.

1LED-WW025

The Pivot Mount Brackets and

the unspecified Fasteners are

part of assembly 1LED-WW025.

The Pivot Mount Brackets ship

attached to the Air Plenum.

9591 (2)

9590 (2)

PIVOT MOUNT BRACKET (2)

1ELECT-FS135 (2)

1ELECT-FS136 (2)

SHRINK TUBE 1 INCH
GSHS-1625W-3/8” Black

1ELECT-FS110

RGB LED

Summary of Contents for SUDZAMELEON ARCH

























































































Search results

Summary of Contents for SUDZAMELEON ARCH

Reviews:

Related manuals for SUDZAMELEON ARCH

Brands by name

Popular brands

Belanger SUDZAMELEON ARCH, Owner'S Manual

Search results

Summary of Contents for SUDZAMELEON ARCH

Reviews:

Related manuals for SUDZAMELEON ARCH

Brands by name

Popular brands