Belanger SUDZAMELEON ARCH Owner'S Manual Download Page 36

Page: 36 / 88

SUDZAMELEON

ARCH

Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

1MANUL956

Installation

Installing the Bayonet Spray Nozzles

1) Locate the six Bayonet Nozzle Kits and verify that the arrows on the check valves are pointing

toward the spray nozzle, as shown below.

2) Locate six nozzles and quick connectors and assemble them together, as shown below.

3) Then secure a nozzle onto each of the Bayonet Nozzle Kits, refer to the image below.

Helpful Hint

The nozzles in the Air Plenum Tri

Nozzles are a 0.5 gpm nozzle for

a total of 3.0 gpm.

Gasket

Helpful Hint

The two Bayonet Nozzles with an
elbow fitting only must be installed
into the Tri Nozzles closest to the
Driver and Passenger Side Legs.

Arrow on

Check Valve

Nozzle

Quick

Connector

Elbow Fitting Only

Tee

Nozzle

Bayonet Kit

Summary of Contents for SUDZAMELEON ARCH

























































































Search results

Summary of Contents for SUDZAMELEON ARCH

Reviews:

Related manuals for SUDZAMELEON ARCH

Brands by name

Popular brands

Belanger SUDZAMELEON ARCH, Owner'S Manual

Search results

Summary of Contents for SUDZAMELEON ARCH

Reviews:

Related manuals for SUDZAMELEON ARCH

Brands by name

Popular brands