Belanger SUDZAMELEON ARCH Owner'S Manual Download Page 51

Page: 51 / 88

SUDZAMELEON

ARCH

1MANUL956

Belanger®, Inc. *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

Utilities

Connecting MixStir® to the Sudzameleon® Arch

Connecting MixStir® to Leg Assembly Manifolds

Replace the ¼” elbow fitting on the Regulator of the MixStir® with the supplied ½” elbow fitting.

2) Run the Compressed Airline Feed from

the Pneumatic Regulator on the MixStir® out to
the Utility Plate on the Sudzameleon®.

3) Run the Chemical Solution Airline Feed from

the Pump on the MixStir® out to the Utility
Plate.

4) Turn on the MixStir® to verify that the chemical

is getting out to the bay and to flush out any
unwanted debris that may be in the line.

5) The MixStir® will be connected to the Leg

Assembly Manifolds through the fittings on the
Utility Plate on the Air Plenum.

6) Connect the Chemical Solution Feedline to the

top  left  fitting  on  the  Utility  Plate  Fitting  and
connect  the  Compressed  Air  Line  to  the  top
right  fitting  on  the  Utility  Plate,  refer  to  the
image below.

7) Turn on the MixStir®, make sure that the solution is spraying out of all six Nozzles properly.

Chemical Solution

Main Feed Line

Pump

Compressed Air
Main Feed Line

MixStir® Air Pump Panel

Supplied ½” Elbow

Fitting to replace

current fitting

Pneumatic

Regulator

Connect Line for
Chemical Solution

Connect Line for
Compressed Air

Utility Plate

Panel for

Bayonet Nozzles

Panel for
Leg Manifolds

Top Fittings to feed

Leg Manifolds

Chemical Solution

Compressed Air

Summary of Contents for SUDZAMELEON ARCH

























































































Search results

Summary of Contents for SUDZAMELEON ARCH

Reviews:

Related manuals for SUDZAMELEON ARCH

Brands by name

Popular brands

Belanger SUDZAMELEON ARCH, Owner'S Manual

Search results

Summary of Contents for SUDZAMELEON ARCH

Reviews:

Related manuals for SUDZAMELEON ARCH

Brands by name

Popular brands