Belanger SUDZAMELEON ARCH Owner'S Manual Download Page 82

Page: 82 / 88

SUDZAMELEON

ARCH

Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

1MANUL956

Maintenance

Replacement Parts

Utility Supply Lines: Chemical Solution & Air Lines for Foam Bullets®

Connect the Chemical Solution &

Compressed Air for the Foam Bullets® to

the middle two Union Fittings

The remaining openings on the Union

Fitting will be used to connect the driver

side Foam Bullet® lines.

Compressed

Air Line

Chemical
Solution Line

Utility Plate

Helpful Hint

The lines for the Foam Bullets® have

extra length for easier installation and

positioning. Do not shorten these lines
until after the Foam Bullets® have been

installed and their desired position has
been determined.

1AIRLN605 (2)

3/8” Black Airline

for Compressed Air

Total Length: 40 FT

(20 FT per side)

1AIRLN600 (2)

3/8” Clear Airline

for Chemical Solution

Total Length: 40 FT

(20 FT per side)

Summary of Contents for SUDZAMELEON ARCH

























































































Search results

Summary of Contents for SUDZAMELEON ARCH

Reviews:

Related manuals for SUDZAMELEON ARCH

Brands by name

Popular brands

Belanger SUDZAMELEON ARCH, Owner'S Manual

Search results

Summary of Contents for SUDZAMELEON ARCH

Reviews:

Related manuals for SUDZAMELEON ARCH

Brands by name

Popular brands