Belanger SUDZAMELEON ARCH Owner'S Manual Download Page 37

Page: 37 / 88

SUDZAMELEON

ARCH

1MANUL956

Belanger®, Inc. *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

Installation

Installing the Bayonet Spray Nozzles

4) Orient the Bayonet Nozzles as shown below. Insert each nozzle into the pre-cut openings in the

side of the Sudzameleon® Tri Nozzles and turn the nozzle clockwise to lock it into place.

5) Verify all six of the spray nozzles are pointing straight down through the middle of their Tri

Nozzle, as shown in the images below.

Note:

When the Bayonet Spray Nozzle is installed properly the spray nozzle will be pointing directly

down through the middle of the Sudzameleon®

Tri Nozzle.

Bayonet Nozzle Kit

Spray Nozzle

After Inserting the Bayonet

Nozzle into the Tri Nozzle turn it

clockwise to lock in place.

Nozzle

Tri Nozzle

Summary of Contents for SUDZAMELEON ARCH

























































































Search results

Summary of Contents for SUDZAMELEON ARCH

Reviews:

Related manuals for SUDZAMELEON ARCH

Brands by name

Popular brands

Belanger SUDZAMELEON ARCH, Owner'S Manual

Search results

Summary of Contents for SUDZAMELEON ARCH

Reviews:

Related manuals for SUDZAMELEON ARCH

Brands by name

Popular brands