Belanger SUDZAMELEON ARCH Owner'S Manual Download Page 40

Page: 40 / 88

SUDZAMELEON

ARCH

Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

1MANUL956

Installation

Installing Check Bodies and Nozzles into the Leg Manifolds

4) Install the 8 supplied Spray Nozzles into the Check Bodies, refer to the image below.

Note:

Lubricate the Nozzle threads with a Liquid-Teflon™ for easier installation and maintenance.

5) Rotate each Nozzle so it is installed at a 5° angle to the centerline of the manifold. See the

image below.

Note:

Refer to the Available Nozzle Choices in the Introduction section to confirm the nozzle types

needed for the application that you purchased. You may need more than one type of nozzle.

Apply Liquid Teflon™ to the

Threads at Installation

Nozzle

5°

Centerline of

Manifold

Summary of Contents for SUDZAMELEON ARCH

























































































Search results

Summary of Contents for SUDZAMELEON ARCH

Reviews:

Related manuals for SUDZAMELEON ARCH

Brands by name

Popular brands

Belanger SUDZAMELEON ARCH, Owner'S Manual

Search results

Summary of Contents for SUDZAMELEON ARCH

Reviews:

Related manuals for SUDZAMELEON ARCH

Brands by name

Popular brands