BEKA BA524D Manual Download Page 9

5.7  Conditioning sub-menu:   Cond

This sub-menu allows the mains (line) frequency at
which the indicator has maximum ac rejection to be
selected and the two internal references to be
calibrated.  These functions are contained in a
sub-menu to minimise the possibility of inadvertent
adjustment.  To gain access to the sub-menu
select 'Cond'  from the main menu and press 

P

.

The indicator will display 'SurE' to warn that
changing the parameters in the sub-menu will
change the indicator display.  Pressing

 P

 again will

give access to the sub-menu, or pressing

 E 

will

return the indicator to the main menu.

5.7.1  AC rejection:   FrE

Caution

If the mains filter frequency is
changed, the indicator display and
internal references (if used) must be
recalibrated.

To provide maximum low frequency rejection the
internal digital filter may be set to operate at 50 or
60Hz to correspond with the local mains (line)
frequency.   To change the frequency select 'FrE'
from the 'Cond' sub-menu and press 

P

 which will

reveal the current setting.  The setting can be
changed by pressing the 

Up

 or 

Down

 buttons

followed by the 

E

 button to return to the sub-menu.

5.7.2  Calibration of internal references:  rEF

The indicator contains two references representing
4 and 20mA.  These references are used in the
'SEt' function which enables the indicator display to
be calibrated without an external current calibrator.
They are also used in the 'C--P' function when the

push-button is programmed to display the input

current in the display mode.   If neither of these
functions is to be used, it is not necessary to
calibrate the internal references.

To calibrate the references select 'rEF' from the
sub-menu and press 

P

  which will result in a

'0.004A' prompt being displayed. Adjust the
external current calibrator to 4.000mA  and again
press 

.  The indicator will display 'Ent' when the

4mA reference has been updated and will then
return to the '.004A' prompt.

To re-calibrate the 20mA internal reference, press
the 

Up

 button which will cause the indicator to

display '.020A'. Adjust the external current
calibrator to 20.000mA  and again press 

P . 

The

indicator will display 'Ent' when the 20mA reference
has been updated and will then return to the '.020A'
prompt.  Two operations of the 

E

 button will return

the indicator to the main menu.

The accuracy of the internal references, and hence
the display accuracy when using the SEt function,  
will  depend upon the accuracy of the external
current source.   With a maximum span of 19999
the indicators have a display resolution of 0.8µA,
we therefore recommend that the accuracy of the
external current source used for calibration is
greater than 0.4µA.

5.8  Function of the 

P

 push-button:   C - - P

This parameter defines the function of the 

P

 push-

button when the indicator is in the display mode.   
While the button is operated the indicator will
display the input current in milliamps or as a
percentage of the span.  

To check or change the parameter select 'C - -P'
from the main menu and press 

P

 to reveal the

current setting.  Pressing the 

Up

 or 

Down

 button

will toggle the setting between '4-20' the current
display and 'PC' the percentage display.  When set
as required press 

E

 to return to the main menu.   

Accuracy of the current display depends upon the
accuracy of the internal references which should be
periodically calibrated - see section  5.7.2

5.9  Security code:  COdE

The calibration and conditioning of the instrument
may be protected by a four digit security code
which must be entered before access to the
programme menu is granted.   New instruments
are programmed with the default security code
0000 which allows unrestricted access to all
programming functions. 

To enter a new security code select 'COdE' from
the menu and press

 P

  which will cause the indica-

tor to display the current security code.  Each digit
of the code can be changed using the 

Up

 and

Down

 push-buttons, and the 

P

 button to move to

the next digit.  When the required code has been
entered press

  E

 to return to the main menu. The

revised security code will be activated when the
indicator is returned to the operating mode.

If the security code is lost, access to the program-
mable functions can be obtained by moving the
internal security link to the override position.   The
security code can then be viewed by selecting
'CodE' from the main menu and pressing

 P

.

9

Summary of Contents for BA524D
























Reviews: