manualshive.com logo in svg

Beckman Coulter DxC 600i, Training Manual, Page: 66 / 101

Share
Download
Beckman Coulter DxC 600i Training Manual Download Page 66

UniCel DxC 600i In-Lab Training Manual A24574-AD 

 

Page 64 

Professional Development Department 

 

October 2010 

Shutdown the DxC 600i System 

 

 

The DxC 600i system may require power down when: 

•

 

Parts replacement procedures specify power to be turned off 

•

 

The lab power goes off 

•

 

The system is moved to a new location 

•

 

Recommended by a BCI specialist for troubleshooting 
purposes 

 
Avoid system errors by following these recommendations: 

•

 

The CTA unit must be powered down whenever the DxC is 
powered down 

•

 

The CTA may be powered down/up without rebooting the 
DxC analyzer if there are no racks on the CTA sample wheel 
or no aliquotted AVs at the AV queue 

 
 
Note:  The Access system is powered down separately at the 
Access analyzer.   
 
Use the flowcharts on the following pages when powering down 
the DxC 600i system. 

 

Summary of Contents for DxC 600i






































































































Reviews:

No comments