Beckhoff eXtended Transport System Operating Instructions Manual Download Page 105

Page: 105 / 114

Fault correction

Version: 2.2

───

105

XTS

12.2.2

Error

12.2.2

Message

Cause

Number of the solution

9000

Xts task cannot be accessed.
Is the context of the TcIoXts
driver set correctly?

Context setting in the "TcIoXtsDrv"
object incorrect

9001

Cycle time "x" µs of XTS task
is not supported! Set cycle
time to 250 µs.

Cycle time of the XTS task is not
equal to 250 µs:
A cycle time of 375 µs is also possi-
ble, but leads to losses of perfor-
mance and dynamics

9002

A XTS mover is lost at "y"
mm. Please restart TwinCAT
to perform a new detection.

Position "y" is at the transition from a
motor module to a power supply mod-
ule:
Incorrect order of the power supply
modules when configuring the XTS or
no reaction or defect of the motor
module at position "y"

9003

The motor module "x" with
name "y" has an error

Error on motor module "x"

9004

Out of memory. XTS mover
count is not supported.

Number of movers in use not sup-
ported

9005

TcIoXts driver has failed to
start up. Please check the
configuration and bootdata
files!

Driver cannot start

9006

Teaching file is invalid.

The stored teaching file does not
match the XTS system

Teaching file originates from a differ-
ent system

9007

Teaching data file "y" is cor-
rupt

The teaching file in the directory "C:
\TwinCAT\3.1\Target\Config\TcIoXts"
is corrupt or missing

9008

Teaching file of XTS module
"x" is invalid

Damaged or missing teaching file in
the directory:

"C:\TwinCAT\3.1\Target\Config
\TcIoXts"

Or motor module "x" not correctly
taught

9009

Saving of teaching file "Beze-
ichnungsstring" ("Designation
string") has failed

The teaching file "Bezeich-
nungsstring" ("Designation string")
could not be saved on the system

9010

Mover "x" is frozen at position
"y" mm

EtherCAT connection interrupted, po-
sition "y" is at the transition from a
motor module to a power supply mod-
ule

Incorrectly order of power supply
modules when configuring the XTS

9011

„…" cannot be loaded. Please
check that the installation is
correct

Driver cannot start

9012

Mover1 cannot be detected.
A general error occurs on
mover "x" during the detec-
tion process.

Mover 1 detection faulty, no mover 1
identified

9013

The SoftDrive "x" is not re-
sponding. Please check the
axis configuration or the Soft-
Drive version.

SoftDrive incorrectly linked or no suit-
able version of the SoftDrive driver for
the TwinCAT configuration

Summary of Contents for eXtended Transport System



















































































































Search results

Summary of Contents for eXtended Transport System

Reviews:

Related manuals for eXtended Transport System

Brands by name

Popular brands

Beckhoff eXtended Transport System, Operating Instructions Manual

Search results

Summary of Contents for eXtended Transport System

Reviews:

Related manuals for eXtended Transport System

Brands by name

Popular brands