Baur PD-TaD 62 User Manual Download Page 97

Page: 97 / 114

PD-TaD 62

Completing a measurement at a later point in time

822-187-3

97 / 114

This chapter discusses how to continue a parallel PD and dissipation factor measurement
and a Full MWT measurement.

If you have saved the log following cancellation of the dissipation factor measurement or
MWT measurement and the PD test, you can complete this measurement at a later point in
time.

1. Depending on the diagnostics type, select the following menu item and press the rotary

knob to confirm:



Parallel PD and dissipation factor measurement:

Main menu

VLF Diagnostics

–

tan



Logs

tan



Measurement



Full MWT:

Main menu

VLF Diagnostics

– tan



Logs

MWT with tan



If the measurement is not complete, this is indicated by a cross.

2. Select the relevant log and press the rotary knob to confirm.

3. In the context menu, select the menu item

Continue measurement

and press the rotary

knob to confirm.

The measurement mode window opens.

Important:

To be able to compare the results, set the same measurement conditions.

Further information:



Chapter

Performing parallel PD and dissipation factor measurements

(on page 66)



Chapter

Performing a Full MWT measurement

(on page 76)

OMPLETING A MEASUREM ENT AT A LATER POINT IN

TIME

Summary of Contents for PD-TaD 62



















































































































Search results

Summary of Contents for PD-TaD 62

Reviews:

Related manuals for PD-TaD 62

Brands by name

Popular brands

Baur PD-TaD 62, User Manual

Search results

Summary of Contents for PD-TaD 62

Reviews:

Related manuals for PD-TaD 62

Brands by name

Popular brands