Baur PD-TaD 62 User Manual Download Page 65

Page: 65 / 114

PD-TaD 62

Parallel partial discharge and dissipation factor measurement

822-187-3

65 / 114

1. In the main menu, select the menu item

VLF Diagnostics

– tan



and press the rotary

knob to confirm.

2. In the

VLF Diagnostics

– tan



menu, select the menu item

tan



Measurement

and

press the rotary knob to confirm.

3. Select the

IEEE 400.2

menu item and press the rotary knob to confirm.

The

IEEE 400.2

window opens.

4. Set the following parameters:



Voltage U (phase

– phase)

Setting range: In accordance with the specifications of the draft IEEEIEEE 400.2 (the
max. test voltage according to the respective VLF HV generator)



Number of measurements per voltage step (1 - 20)



Number of phases (1 - 3)



Test type

The following test types are available: Installation, acceptance inspection
(commissioning) and maintenance.

The max. voltage is automatically determined and displayed after voltage U (phase

–

phase) has been entered.

5. Select the

Next

menu item and press the rotary knob to confirm.

The dialog for selecting the evaluation opens. The cursor is in the input field for the
evaluation.

6. Press the rotary knob in order to select an evaluation.

7. In the context menu, select whether you wish to use evaluation criteria for America or for

other countries (World) according to IEEE 400.2, and press the rotary knob to confirm.

Summary of Contents for PD-TaD 62



















































































































Search results

Summary of Contents for PD-TaD 62

Reviews:

Related manuals for PD-TaD 62

Brands by name

Popular brands

Baur PD-TaD 62, User Manual

Search results

Summary of Contents for PD-TaD 62

Reviews:

Related manuals for PD-TaD 62

Brands by name

Popular brands