Baur PD-TaD 62 User Manual Download Page 19

Page: 19 / 114

PD-TaD 62

Product information

822-187-3

19 / 114

No.

Element

Function

Mains voltage
connection

Is used to connect the Power Box to the mains voltage

When the mains voltage is connected, the LED next to the mains voltage
connection lights up.

Device protection fuse

Used to protect the Power Box and connected system components

Type: T 16 AH

Laptop

port

Is used to connect the laptop

The laptop is used for data transmission and is connected to the Power Box
via the Ethernet cable (included in the standard delivery).

PD Detector

port

Is used to connect the PD measuring unit of the PD-TaD 62

The PD measurement unit is connected to the Power Box via a PoE cable.
The PoE cable is used for the power supply of the PD-TaD 62 and for data
transmission.

Ports for system power
supply

Are used to connect the VLF HV generator and the laptop to the power
supply on the Power Box

Max. current 16 A

3.5

HF filter

The HF filter is used to minimise external influences on the measurement results. The HF
filter is supplied in the PD-TaD 62 transport case.

Summary of Contents for PD-TaD 62



















































































































Search results

Summary of Contents for PD-TaD 62

Reviews:

Related manuals for PD-TaD 62

Brands by name

Popular brands

Baur PD-TaD 62, User Manual

Search results

Summary of Contents for PD-TaD 62

Reviews:

Related manuals for PD-TaD 62

Brands by name

Popular brands