manualshive.com logo in svg

Bauer Rainstar TX Plus E, Operating Manual, Page: 77 / 92

Share
Download
Bauer Rainstar TX Plus E Operating Manual Download Page 77

 
 

 

Operating manual for 

BAUER RAINSTAR series

 TX Plus 

69 

 

 

BAUER change-speed gearbox reduces the turbine speed 
according to the set retraction speed. 
The gearbox incorporates four gears.  Reel drive stop at the 
end of the irrigation strip is ensured by disengagement of the 
tooth clutch.   

 

 
The four-speed gearbox allows you to adapt the system precisely to existing operating conditions. As a result 
the following retraction speeds [m/h] can be reached: 
 

 

 

GEAR SELECTION

 

 
 

TX 20

1

8

--

20

m / h

2

16

--

32

m / h

3

28

--

50

m / h

4

> 45

m / h

 

 

 

 

 

 

 

 

 

 

 

Removal of the drive cover for service is only permitted when the PE-pipe is 
completely slack and the water supply turned off  ! 

The gear shift lever must be moved to the shut-off position ! This shut-off position 
must also be used for transporting the machine on the road !     

 

 

 

WARNING!

 

Summary of Contents for Rainstar TX Plus E





























































































Reviews:

No comments