manualshive.com logo in svg

Bauer Rainstar TX Plus E, Operating Manual, Page: 47 / 92

Share
Download
Bauer Rainstar TX Plus E Operating Manual Download Page 47

 

 

Operating manual for 

BAUER RAINSTAR series

 TX Plus 

39 

 

6.11.4  LIMIT STOP FOR TURBINES – REGULATING VALVE WITH ECOSTAR 4300 

 
See point 6.5. The regulating area of the regulating valve of the turbine needs to be adjusted to the respective 
delivery rate. If the limit stop is not adjusted correctly it might happen that the turbine cannot be regulated, this 
means that the PE-pipe retraction happens with maximum speed.  
 
If the flow rate is reduced significantly the limiting bolt head needs to be adjusted again, as otherwise the retraction 
speed listed on the performance chart cannot be reached.    
 
You can see the required delivery rate on the performance chart fixed on the machine below the nozzle sizes. 

6.11.5  SHORT CHECKLIST fOR ECOSTAR 4300 

 
1.  Check battery voltage (should be 12 V minimum) 

a)  Cover solar panel completely  
b)  See battery voltage In test menu 1 (press MENU key once) 
c)  If there is no or not enough power available (below 12 V), check battery, cable connections or fuses inside 

the electronic box. 

 

2.  Check function of the sensors 

a)  Set test menu 2  (press MENU key twice) 
b)  The display show indications for function control of the installed sensors , Motor 1 -Motor 2 

 

3.  Check length indicator of the laid down PE-pipe 

(press  MENU key once )

 

a)  Read out the pipe length of the laid down PE-pipe on the standard display and compare with the engraved 

length indication on the PE-pipe.  

b)  If it shows 000 m, or significpless than the length of the laid out pipe, you need to make settings. 

 

4.  Check of the mechanic transmission to the stop sensor. 

 

5.  Adjustment of the limiting bolt for the tooth segment of the regulating valve according to the chart 

fixed on the machine. 

 

Summary of Contents for Rainstar TX Plus E





























































































Reviews:

No comments