manualshive.com logo in svg

Bauer Rainstar TX Plus E, Operating Manual, Page: 65 / 92

Share
Download
Bauer Rainstar TX Plus E Operating Manual Download Page 65

 
 

 

Operating manual for 

BAUER RAINSTAR series

 TX Plus 

57 

16 

LOW-PRESSURE OR UNDERPRESSURE SHUT-OFF VALVE 

(OPTIONAL with ECOSTAR 4300) 

 

 
With the low pressure shut-off valve option, a diaphragm valve is opened quickly at the end of the irrigation run, 
releasing a big water stream into the open. This causes sudden pressure decrease in the supply line (to about 
half the original pressure).  Through this drop in pressure a pressure switch shuts off the pumping unit and thus 
also the water supply.   
Therefore this valve can only be used in combination with an automatic pump shut-off device.   
 

17  LOW-PRESSURE OR UNDERPRESSURE SHUT-OFF VALVE 

(OPTIONAL with mechanical speed control)   

 

 

 

With the low pressure shut-off valve option, a diaphragm valve 
is opened quickly at the end of the irrigation run, releasing a 
big water stream into the open. This causes sudden pressure 
decrease in the supply line (to about half the original 
pressure).  Through this drop in pressure a pressure switch 
shuts off the pumping unit and thus also the water supply.   
Therefore this valve can only be used in combination with an 
automatic pump shut-off device. 

 

 

 

Before starting up with water again the hand lever of the 
three-way cock must be shifted to the START position 
(downward) - the shut-off valve is relieved and opens. 

 
 

Summary of Contents for Rainstar TX Plus E





























































































Reviews:

No comments