manualshive.com logo in svg

Bauer Rainstar TX Plus E, Operating Manual, Page: 28 / 92

Share
Download
Bauer Rainstar TX Plus E Operating Manual Download Page 28

 
 

Operating manual for 

BAUER RAINSTAR

 

Series TX Plus 

20 

6 ECOSTAR 4300 

ReTRACTION SPEED CONTROL 

 

        

 

 

6.1 General 

 

The 

BAUER ECOSTAR 4300

 

allows you to operate your irrigation machine with ease at the touch of a 

button. 
 
An illuminated four-line display offers you comprehensive indication of the machine’s current operational status.  
 
Through permanent comparison of set-point and actual value of the retraction speed you can administer the 
precipitation rate you need. 
 
The 

ECOSTAR 4300

 consists of the electronic box, a cable harness with the connected sensors for the PE- pipe 

length retraction speed and shut-off as well as connections for battery, solar panel and the turbine regulation 
motor.  
Connections are also provided for installing a pressure switch and an electric shut-off valve (both optional). 
 
 
The electronic system of the ECOSTAR

 4300

 is rigidly built and has been tested under different climatic conditions.  

If problems still occur it is advisable to exchange the complete electronic box. If a sensor is defective it is possible 
to exchange only the sensor, too. 
 
 
 
 
 

Summary of Contents for Rainstar TX Plus E





























































































Reviews:

No comments